6
EN- Safety Instructions
•
The appliance shall be installed by a
qualified person in accordance with
the regulations in force to keep the
warranty applicable. The manufacturer
shall not be held responsible for
damages arising from procedures
carried out by unauthorized persons
which may also void the warranty.
•
It is customer’s responsibility to prepare
the location the appliance shall be
placed on and to have the electrical
installation prepared.
•
The appliance shall be installed in
accordance with all local gas and/or
electrical regulations.
•
Remove all packaging material and
documents inside the appliance and
check for any damage on the appliance
before the installation. Do not have it
installed if the appliance is damaged
•
Make sure that the user cannot reach
the electrical connections after the
installation.
•
Always wear protective gloves during
transportation and installation.
•
Disconnect electrical connections in the
area of installation before starting the
installation.
•
Surfaces of the furniture that the
appliance shall be installed shall be heat
resistant (100 °C minimum).
•
Make sure that the furniture is in
straight, horizontal position and that
it is fixed before the installation of the
appliance.
•
Do not install heat insulation strips to
the furniture that the appliance shall be
installed.
•
Dimensions given in installation
diagrams are in mm.
Preparation of the furniture
that the appliance shall be
installed (Figures 1-2-3)
The appliance is designed for installation into
commercially available work tops. A safety
distance shall be left between the appliance
and the kitchen walls and furniture. (Figure 1)
The clearance where the appliance shall be
placed on the worktop shall be cut as per
the dimensions given figure 1.
* If there is no hood on the appliance, allow a
distance of 750 mm from the hob surface to
the furniture.
If a shroud/hood is installed above the
appliance, allow a distance for the installation
height as described in the operating manual
of the shroud/hood.
** Minimum distance between the cabinets
shall be equal to the width of the hob
Flush-fit installation: (Figure 2)
•
If you want to install your appliance as
flush-fit with the worktop, refer to Figure
2 for the cutting dimensions of your
worktop.
If the appliance shall be installed
above a drawer: (Figure 3a)
•
If the appliance shall be installed on a
drawer, a wooden plate/sheet shall be
installed between the drawer and the
cooker. A clearance with the specified
dimensions shall be allowed. (Figure 3a)
•
A minimum distance of 65 mm shall be
allowed between the wooden plate and
the worktop surface. (Figure 3a)
•
Ventilation: An adequate ventilation
shall be provided in the area under the
appliance for the efficient operation
of the appliance. For this purpose,
a ventilation hole with the minimum
dimensions of 550x45 mm shall be
opened as shown in Figure 3a.
If the appliance shall be installed
above an oven: (Figure 3b)
•
* Worktop thickness shall be at least 28
mm. This dimension shall be at least 32
mm if you will install your appliance as
flush-fit. (Figure 3b)
•
Ventilation: An adequate ventilation
shall be provided in the area under the
appliance for the efficient operation of
the appliance. A minimum distance of 4
mm shall be allowed between the lower
surface of the cooker and the upper
wall of the oven (Figure 3b) to provide
adequate ventilation. Additionally, a
cross-section with the dimensions of
35x500 mm shall be left in the bottom
of the furniture housing where the oven
is placed. (Figure 3b)
Ventilation
•
Ventilation affects the heating
performance of the appliance directly.
Even if no problem is detected in the
Содержание HII64210FMTR
Страница 2: ...2 Ø 4 x 6 5 mm x6 Ø 3 19 x 16 mm x2 ...
Страница 5: ...5 60 cm 70 cm 80 cm 90 cm 6 7 8 9 ...
Страница 108: ...HE התקנה הוראות R AE 22 09 2021 185 2620 93 ...