Beko FLM SF53 Скачать руководство пользователя страница 35

Страница: 35 / 44

Installation and operating manual

35 METPOINT

SF53

6.5. Pulse / alarm

Setup

→

Pulse/Alarm

The galvanically isolated pulse output can be used as a pulse or as an alarm output.

The following units can be selected for the alarm output:

•

kg/min, cfm, l/s, m³/h, m/s, °F, °C, kg/s

Press "Value" to enter the alarm value. Press "Hyst". to enter the desired
hysteresis.

Hi-Lim:

upper limit

Lo-Lim:

lower limit

The following units can be selected for pulse output:

•

kg, cd, l, m³

Select "Value" to enter the pulse factor (0.1, 1, 10, 100). Select "Polarity" to enter
the switching state (plus = 0

→

1, minus = 1

→

6.5.1. Pulse output

The maximum permissible number of pulses per second is 50. Pulse output is delayed by 1 second.

Pulse factor

[m³/h]

[m³/min]

[l/min]

0.1 ltr / pulse

0.3

300

1 ltr / pulse

180

3000

0.1m³ / pulse

18000

300

300000

1 m³ / pulse

180000

3000

3000000

Table 1: Maximum flow volumes for pulse output

NOTICE

Important information

Pulse factors that are unsuitable to represent the measuring range limit value are not permissible. Such
entries are discarded and an error message is displayed.

Содержание FLM SF53













































Результаты поиска

Содержание FLM SF53

Отзывы:

Бренды по названию

Популярные бренды

Beko FLM SF53, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FLM SF53

Отзывы:

Бренды по названию

Популярные бренды