Beko DC 1560, Руководство пользователя

Страница: 5 / 17

5 - EN
2
Installation
Refer to the nearest Authorised Service Agent
for installation of your product.
C
Preparation of location and electrical
installation for the product is under
customer’s responsibility.
B
Installation and electrical connections must
be carried out by a qualified personnel.
A
Prior to installation, visually check if the
product has any defects on it. If so, do not
have it installed. Damaged products will
cause risks for your safety.
Appropriate installation location
• Install the product in an environment which
has no risk of freezing and is in a stable
and level position.
• Operate your product in a well ventilated,
dust-free environment.
• Do not block the air ducts in front of and
under the product with materials such as
long pile rugs and wooden bands.
• Do not place your product on a long pile
rug or on similar surfaces.
• Do not install the product behind a door
with a lock, sliding door or a hinged door
which can strike the product.
• Once the product is installed, it should stay
at the same place where its connections
have been made. When installing the
product, make sure that the rear wall of it
does not touch anywhere (tap, socket, etc.)
and also pay attention to install the product
at a place where it will stay permanently.
B
Do not place the product on top of the
power cable.
• Keep at least 1.5 cm distance to walls of
other furniture.
Under counter installation
• A special part (Part no: 295 970 0100)
replacing the top trim must be provided
and installed by the Authorised Service
Agent in order to use the machine under a
counter or in a cupboard. It should never
be operated without the top trim.
• Leave at least 3 cm of space between
the side and rear walls of the product and
the walls of the counter/cupboard when
installing your product under a counter or in
a cupboard.
Mounting over a washing machine
• A fitting device should be used between
the two machines when installing above a
washing machine. The bracket (Part no.
296 280 0100 white/296 280 0200 grey)
must be installed by the Authorised Service
Agent.
• Place the product on a firm floor. If it will be
placed on top of a washing machine, the
approximate weight of both machines may
reach 180 kg when they are full. Therefore,
the floor must be capable of carrying the
load on it!
Ventilation hose and connection
(for products equipped with an
outlet vent)
Ventilation hose allows exhaust air from inside
the machine
Vented dryer has 1 air outlet.
Stainless sheet metal or aluminum pipes can
be used instead of a hose. The pipe diameter
should be minimum 10 cm.
Maximum hose and pipe lengths are given in
the table below.
Hose Pipe
Maximum length 4 m 5 m
1 elbow 45° -1.0 m -0.3 m
1 elbow 90° -1.8 m -0.6 m
1 elbow 90° short -2.7 m
1 wall passage -2.0 m -2.0 m
C
Each elbow and other passages should
be subtracted from the maximum length
stated above.
To connect a ventilation hose;
1. Connect the air outlet hose to the
hose spacer piece by turning it
counterclockwise.
2. Make the hose passages as shown below.
C
Exhaust of humid air from the dryer into the
room is inconvenient. It may damage the
walls and furniture in the room.
C
The ventilation hose can be routed outdoors
via a window or it can be connected to the
air outlet in the bathroom.
C
Air outlet hose must be routed directly to the
outdoors. There must be a limited number
of elbows as not to hinder ventilation.
C
To prevent water accumulation in the hose,
make sure that it is not folded on the floor.
B
The ventilation hose should not be
connected to the chimney of a stove or a