Beko BEKOMAT 12i Скачать руководство пользователя страница 47

Страница: 47 / 76

9. Operation

9.1 Warning notices

DANGER

Operation outside the permissible limit range!

Operation of the product and accessories outside the permissible limits and operating

parameters, unauthorised intervention and modifications may result in death or serious

injury.
•

Adhere to the limits and operating parameters specified on the type plate and in the

manual.

• Adhere to the assembly conditions and ambient conditions.
• Check whether the operating parameters have been amended or restricted by the use of

accessories.

• Adhere to the maintenance intervals.

DANGER

Electric voltage!

There is a danger of death or serious injuries as well as malfunction and device failure
following contact with components which are in contact with electric voltage.
• Only operate the product with the cover or housing complete and closed.

NOTE

Operating personnel!

Insufficient knowledge of the product and the accessories can lead to damage to property

and the environment as well as impair operation.
•

The product and accessories may only be operated and used by qualified operating

personnel.

Original installation and operation manual

BEKOMAT

12i / 12i CO / 12i CO PN63

47 | 76

Содержание BEKOMAT 12i













































































Результаты поиска

Содержание BEKOMAT 12i

Отзывы:

Бренды по названию

Популярные бренды

Beko BEKOMAT 12i, Оригинальное руководство по установке и эксплуатации

Результаты поиска

Содержание BEKOMAT 12i

Отзывы:

Бренды по названию

Популярные бренды