background image

decimal points for a few seconds while the new
information is stored in permanent memory.

All new BA578C indicators are supplied calibrated
as requested at the time of ordering.  If calibration
is not requested, the transmitter will be set for 3
wire RTD input with 4 to 20mA output correspond-
ing to a display of 0.0°C to 100.0°C.

5.1 Summary of Programme Menu functions

The parameters which may be programmed vary
depending upon which input is selected.  For:

Thermocouple and resistance 
thermometer inputs 

The BA578C transmitter will always display
sensor temperature.  Programming allows the
display to be in degrees centigrade or Fahren-
heit, and for the display resolution to be
selected.

Zero and span of the 4/20mA output current
may be programmed to represent any display
range.

Voltage input

The display may be programmed to show the
input  voltage in any engineering units.

Zero and span of the 4/20mA output current
may be independently programmed to repre-
sent any displayed value. 

Each of the functions in the Programme Menu is
described in the following summary with a cross
reference to more detailed information.   Figs 5A
and 5B illustrate the location of each function within
the menu.  

 

Display        Summary of Programme Menu

                                         functions

'InPut'

Transmitter input

Conditions the transmitter to accept
thermocouple 'tHC', resistance
thermometer 'rtd' or a voltage 'UOLt'
input.
See section 5.2.1

For Thermocouple Inputs

'tYPE'

Sensor type

Selects the type of thermocouple input.
See section 5.3.1

'dEg'

Units of display

Sets display to 

o

C or

 o

F.

See section 5.3.2

'rESn'

Display resolution

Selects low or high display resolution.
See section 5.3.3

'CJC'

Cold junction compensation

Turns thermocouple cold junction
compensation ON or OFF.
See section 5.3.4

'burn'

Input open circuit drive

Selects up scale drive, down scale drive
or no drive when input is open circuit. 
See section 5.3.5

For Resistance Thermometer Inputs

'tYPE'

Sensor type

Selects 3-wire, 4-wire or differential
Pt100 resistance thermometer input.
See section 5.4.1

'dEg'

Units of display

Sets display to 

o

C or

 o

F.

See section 5.4.2

'rESn'

Display resolution

Selects low or high display resolution.

See section 5.4.3

      7

Содержание BA578C


























Отзывы: