background image

5.17 Local reset of total and grand total.
         ‘LoC. R5Et’

This  function  contains two sub-functions  ‘t-rE5Et’
and ‘Gt-rE5Et’ which allow the total display and the
grand  total  to  be  independently  reset  using  the
instrument  push  buttons  without  access  to  the
configuration menu from the operating mode. 

When enabled, ‘t-rE5Et’ allows an operator to reset
the BA554E total display to zero by operating the

 and

 

 push buttons simultaneously for at least

two seconds.    To check the status of ‘t-rE5Et’
select 'LoC.r5Et'' from the configuration menu and
press

 

P.

   Using the 

 or 

 button select ‘t-rE5Et’

and  press  

P

  which  will  reveal  if  the  function  is

turned 'on' or 'oFF'.   Operating the 

 or 

 button

will toggle the display between the two conditions.
When set as required  pressing the

 

E

 

button  will

enter   the   selection   and   return   the   display   to   the
‘t-rE5Et’  sub-function.    The  remote  reset  facility
described  in  section  3.2  of  this  manual  is  not
affected by the status of this local reset function.

When  enabled,  ‘Gt-rE5Et’  allows  an  operator  to
reset the BA554E grand total to zero by operating
the  

E

 and

 

 push buttons simultaneously for at

least ten seconds.  To check the status of ‘t-rE5Et’
select 'LoC.r5Et'' from the configuration menu and
press

 

P.

   Using  the  

 or  

 button  select

‘Gt-rE5Et’  and  press  

P

  which  will  reveal  if  the

function is turned 'on' or 'oFF'.   Operating the 

 or

 button will toggle the display between the two

conditions.  When set as required pressing the

 

E

button  will  enter  the  selection  and  return  the
display to the  ‘Gt-rE5Et’ sub-function.

5.18  Security code:  ‘CodE’

Access to the instrument configuration menu may
be protected  by a  four  digit  security  code  which
must be entered to gain access.   New instruments
are configured with the default security code 0000
which  allows  unrestricted  access  to  all
configuration functions. 

To enter a new security code select 'CodE' from
the  configuration  menu  and  press

 

P

 which  will

cause  the  Rate  Totaliser  to  display  the  existing
security code with one digit flashing.  The flashing
digit  can  be  adjusted  using  the  

 and

 

 push

buttons,  when  set  as  required  operating  the  

P

button will transfer control to the next digit.   When
all the digits have been adjusted press

 

E

 to return

to  the  ‘CodE’  prompt  in  the  configuration  menu.
The revised security code will be activated when
the Rate Totaliser is returned to the display mode.
Please contact BEKA associates sales department
if the security code is lost.

5.19  Reset to factory defaults:  ‘r5Et’

This function enables the Rate Totaliser and the
lineariser  to  be  quickly  returned  to  the  factory
default  configurations  shown  in  sections  5.2  and
6.5

To  reset  the  Rate  Totaliser  or  lineariser  select
‘r5Et’ from the configuration menu and press 

P

, the

Rate Totaliser will display one of the reset options
‘ConF’ or ‘LtAb’.   

‘ConF’

Resets the Rate Totaliser to defaults

‘LtAb’

Resets the lineariser to defaults

Using the 

 or 

 push button select the required

sub-function and press  

P.

   To prevent accidental

resetting  the  request  must  be  confirmed  by
entering ‘5urE’.   Using the 

 button set the first

flashing digit to ‘5’ and press  

P

 to transfer control

to  the  second  digit  which  should  be  set  to  ‘u’.
When  ‘5urE’  has  been  entered  pressing  the  

E

button will reset the selected configuration menus
and return the display to the ‘r5Et’ function in the
configuration menu. 

5.20  Over-range

Numerical over-range of the rate or total displays is
indicated by all the digits displaying ‘9’ and all the
decimal points flashing. 

When  the  total  display  exceeds  99999999  or
-9999999 it will not automatically roll-over to zero
and  continue  counting,  but  the  grand  total  will
continue to count.   If it is likely that the total will
exceeds  99999999  or  -9999999  the  grand  total,
which  has  a  capacity  of  10

16

 and  –10

15

 counts,

should be reset to zero at the start of the operation.

If the total display exceeds 99999999 or -9999999
when the BA554E has been configured for          bi-
directional flow, the total display will be locked and
will not record flow in the opposite direction to the
over-range, although the grand total will continue
to function.

17

Содержание BA554E


































Отзывы: