BEKA BA454D Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 49

BEKA BA454D Скачать руководство пользователя страница 13

5. INSTALLATION

5.1 Location

The  BA454D  batch  controller  is  housed  in  a
robust  IP66  glass  reinforced  polyester  (GRP)
enclosure  incorporating  an  armoured  glass
window and stainless steel fitting.  It is suitable
for  exterior  mounting  in  most  industrial
environments,  including  off-shore  and  waste
water  treatment  installations.    Please  consult
BEKA  associates  if  high  vibration  is
anticipated.

The BA454D enclosure is surface mounting.
Accessory kits described in sections 9.2 of this
manual enable the instrument to be mounted
onto a vertical or horizontal pipe.

The field terminals and the two mounting holes
are located in a separate compartment with a
sealed cover allowing the instrument to be
installed without exposing the display
assembly.

The BA454D earth terminal is connected to the
internal  EMC  filters.  For  maximum  radio
frequency  interference  rejection  this  terminal
should be connected to a local earth, or to a
cable screen which is earthed in the safe area.
The  BA454D  enclosure  is  supplied  with  a
bonding  plate  to  ensure  electrical  continuity
between the three conduit / cable entries.

5.2 Installation Procedure

Fig 9 illustrates the instrument installation
procedure.

a.

Remove the instrument terminal cover by
unscrewing the two captive 'A' screws.

b.

Mount the instrument on a flat surface
and secure with two M6 screws through
the 'B' holes. Alternatively use one of the
mounting kits described in section 9.2

c.

Remove  the  temporary  hole  plug  and
install  an  appropriate  IP  rated  cable
gland or conduit entry.  If more than one
entry is required, one or both of the IP66
stopping plugs may be replaced with an
appropriated  IP  rated  cable  gland  or
conduit fitting.

d.

Connect the field wiring to the terminals
as shown in Fig 10.

e.

Replace the instrument terminal cover
and evenly tighten the two 'A' screws.

Fig 9 BA454D installation procedure

5.3 EMC

The BA454D complies with the requirements of
the  European  EMC  Directive  2004/108/EC.
For specified immunity all wiring should be in
screened twisted pairs and the BA454D earth
terminal  should  be  locally  earthed  or
connected to a cable screen which is earthed
in the safe area.

To prevent circulating currents, cable screens
should only be earthed at one point in the safe
area.

13

«
...
11
12
13
14
15
...
»

Содержание BA454D


















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды