background image

Initial commissioning  |  Start Line MS 201  |  35

en

1 695 108 073

  2016-07-27

Bosch Automotive Service Solutions srl

6.2 

Fastening the MS 201

 

!

For the procedure when lifting the MS 201, 
please see the figure. Lift the MS 201 carefully 
(the middle of the MS 201 is not identical with 
the center of gravity) and protect the plastic covers 
to prevent damaging them.

1. 

Detach the bolts and nuts fixed on the machine 
chassis. 

2. 

Bind the hoist tape (mod. DR 750 of 3 m and DR 
735 of 1.5 m factor 6:1).

3. 

Lift the MS 201 carefully. 

4. 

Remove the pallet and position the MS 201 at 
the preselected location.

 

!

Ensure that the nozzle and air hose on the 
MS 201 are not damaged during the hoisting 
operation. Be very careful when lifting the 
MS 201.

 

i

If tires will be inflated on the turntable, you must 
secure the MS 201 to the floor.

5. 

Use an M10 bolt (grade 12.9), placed through the 
hole in the pallet, to secure the MS 201 to the 
floor.

6.3 

Connecting the MS 201 to power 

and the compressed air supply

 

!

In accordance with the electrical specification, the 
voltage supply must be equipped with a fuse and a 
properly grounded protective conductor connection 
as well as a safety switch.

 

i

If the MS 201 does not have a plug, the user 
should prepare a 16 A plug suitable for the operating 
voltage of the tire changer and as specified in the 
electrical code.

1. 

Connect the MS 201 to the voltage supply. 

 

R

The voltage deviation should be 0.9 - 1.1 times the 
rated voltage range, and the frequency deviation 
should be 0.99 - 1.01 times the rated frequency 
range. You should take the necessary protective 
methods.

 

R

Only qualified personnel should make the 
connection to the voltage supply.

 

R

If the MS 201 is not being used, please 
disconnect the power promptly to ensure that the 
MS 201 is not switched on accidently.

 

R

If the MS 201 will not be used for a long time 
and the machine is connected directly to the 
electrical cabinet instead of via a plug, the electrical 
cabinet should be locked. Only professional 
personnel should be able to open the electrical 
cabinet in order to ensure that the MS 201 is not 
switched on unintentionally.

 

!

The MS 201 must be grounded and the 
protective conductor must not be attached to a 
heater, plumbing pipe, telephone cable or the like.

2. 

The compressed air supply must comply with the 
requirements for the tire changer. The details of 
these requirements are specified in "Technical 
parameters" section. The pressure and volumetric 
flow of the compressed air supply should meet the 
requirements of the MS 201. The pressure must 
be between 8 and 16 bar.

3. 

Use the special air hose to connect the water 
separator, air regulator and lubricator on the side of 
the MS 201 (see figure). 

4. 

Please make sure that the oil has been fully filled 
reaching the standard oil level. The oil contained 
in the lubricator should be SAE 20 oil, or the air 
passage will not be lubricated, causing the sealing 
kits to be damaged in a short time.

 

R

The user must mount an air supply shut-off valve and 
pressure control valve in front of the MS 201.

6.4 

Checking the pedal functions

 

Depress the turntable rotation control pedal 7-4; the 
turntable will rotate clockwise. 

 

And rise up the turntable rotation control pedal 7-4, 
the turntable will rotate counterclockwise.

 

Step down the horizontal arm control pedal 7-1 
to the lowest position and the horizontal arm will 
swing out. 

 

Go on to step down the horizontal arm control pedal 
to highest position the horizontal arm will swing 
back to the vertical position.

 

Depress the blade control pedal 7-3; the blade 
executes its function. 

 

Release the blade control pedal 7-3 and the pedal 
returns to its original position.

 

Step down the clamping jaw open/close control 
pedal 7-2 to the first gear and the clamping jaw will 
open. 

Содержание Start Line MS 201


























Отзывы: