background image

Page  6

Currently national standards enforceable in the installation country covering the installation and use of gas powered
equipment are to be respected, as are standards covering smoke dispersion and ventilation of enclosed areas, even
though gas detection equipment is installed.
Essential  element  for  the  correct  functioning  of  the  detector  is  its  correct  installation.
Following  the  suggestions  in  this  section  you  will  get  a  high  accuracy  combined  with  a  total  absence  of  false
alarms.
The  RGX100  is an equipment  adapted  to be mounted  externally on a wall. Installing, it  is  fine to use  ordinary
care  that  requires  an  electronic  device,  and  then:
-  Install  the  detector  away  from  sources  of  excessive  heat.
-  Avoid  that  liquids  come  into  contact  with  the  detector  RGX100,    remembering  that  its  external  structure  has
degree  of  protection  IP42.

The  detector  should  not  be  installed:
-  
in  environments  where  the  temperature  drops  below  10  °  C  or  rises  above  40  °  C.

The  detector  is  equipped  to  detect  different  types  of  gases,  and  according  to  these,  its  must  to  be  positioned
at  different  heights.
These  heights  are:
-  30  cm  from  the  lowest  point  of  the  floor  in  order  to  detect

heavy  gases  (LPG,  etc)

-  30  cm  from  the  highest  point  of  the  ceiling  in  order  to  detect

light  gase  (Methane  etc)

-  Install  detectors  from  1  to  4  m  from  gas  appliances

The installation of the detector does not exempt from ... ... The compliance with all regulations concerning the
characteristics, installation and use of gas appliances. The ventilation of the spaces and the elimination of combustion
products are described in the UNI norms according to ART. 3 LAW 1083 / 71 and relevant legal provisions.

METHANE gas detector
max. 30 cm from the ceiling

LPG gas detector
max. 30 cm from the floor

Installation measures and positioning

Caution!!
Do  not  install  the  detector  near:
sinks,  air  intakes,  heating  or  air
conditioning systems, windows and
ventilation devices.

Содержание RGX100









Отзывы: