6
EUROPOWER PMX1000/PMX3000/PMX5000
2. CONTROL ELEMENTS
considerably higher than the power provided to the
speakers wired to the parallel speaker outputs.
Please read the information given on the rear panel
of the power mixer.
+
Information on how to properly connect your speaker
with regard to polarity can be found on the rear of
the unit (PIN assignment) (see also
and
).
PMX5000: Use the
BEHRINGER SPEAKER PROCESSING
switch to activate a filter that allows you to adapt the mixer
to the characteristics of your loudspeakers. If the speakers
have a limited frequency response in the bass range, this
function allows you to filter this range at the output signal
of the mixer and thus adapt it optimally to the frequency
response of the speakers.
PMX1000/PMX5000:
If
STANDBY
is pressed, all input
channels are muted. During pauses you can prevent the
microphones from picking up noise or interference, which
would then be reproduced by the P.A. system or possibly
damage the speaker diaphragms. The benefit is that all
faders can be left untouched while you play back music
from CD via the CD/TAPE inputs (see
). There is also
no need to move the faders and lose your mix.
2.2 Equalizer and FBQ
Your power mixer features a graphic 7-band equalizer,
which allows you to fine-tune the sound depending on the
room acoustics. In the center position the frequency
response is not effected. To boost or cut a certain
frequency range, simply move the corresponding fader
upward or downward respectively.
+
Please note that the equalizer behaviour depends
on the position of the AMP MODE switch (see
).
Press the
FBQ IN
switch to activate the Feedback Detection
system (the FBQ will be active only if you have switched
on the equalizer
before). Frequencies causing
feedback are shown by brightly lit fader
LEDs. All other LEDs will be darker. Now,
cut the frequency range in question until
feedback disappears (the LED gets darker
or goes out). This function is available for
both the main and monitor mix.
PMX1000: The switch
FBQ FEEDBACK DETECTION
performs the same function as on the PMX3000 and
PMX5000
.
Use the
MAIN/MON 1
switch to select whether the equalizer
processes the main or the monitor mix. When not pressed,
the stereo equalizer processes only the main mix. When the
switch is pressed, the EQ processes only the monitor mix.
PMX1000: The
MAIN MIX/MONITOR
switch performs the
same function as on the PMX3000 and PMX5000
.
Press the
EQ IN
switch to activate the equalizer. The fader
LEDs illuminate when the EQ is on.
Use this LED display to control the output level of the main
signal. The upper
LIM
LED illuminates when the internal
amp protection circuit responds to levels that are too high.
PMX1000: The POWER LED is illuminated when you switch
the unit on.
+
The LIM LEDs and the LED display do NOT light up when
an external signal is fed in via the PWR AMP INSERT
jacks
.
2.3 Effects section
List of all multi-effects processor presets.
The LED level meter on the effects module should always
show a sufficiently high level. Make sure that the Clip LED
illuminates with signal peaks only. If it is constantly illu-
minated, the effects processor is overloading, which can
lead to unpleasant distortion. The
FX SEND
fader
(PMX1000)
or
FX/FX 1/2
fader (PMX3000/PMX5000) controls the level
sent to the effects module and to the FX SEND output
jacks.
The effects display always reads the currently selected
preset.
PMX3000/PMX5000: Press the
FX1/2 IN
switch to activate
the effects processor.
PMX1000/PMX3000: Turn the
PROGRAM
control to select
an effects algorithm (preset number starts flashing). Press
this control to activate the effect selected.
+
PMX1000: The effects processor is operative all the
time. Adjust the effect intensity for the MAIN or
MON signals with controls
o r
respectively.
PMX5000: The PMX5000 has two separate effects
processors, which can be used independently of one
another. Enable one or both processors with the FX1/2 IN
buttons.
PMX3000/PMX5000: The
FX 1/2 TO MON 1
control allows
you to set the intensity of the multi-effects processors in
the monitor mix. No effect is sent to the monitor mix when
this control is set fully counter-clockwise.
PMX1000: The
FX TO MON
control performs the same
function as on the PMX3000 and PMX5000.
The
FX 1/2 TO MON 2
control allows you to determine the
effect intensity of the multi-effects processor in the monitor
2 mix. No effect is sent to the monitor 2 mix with this control
turned fully counter-clockwise.
The
FX 1/2 TO MAIN
control allows you to determine the
effect intensity of the multi-effects processor in the main
mix. No effect is sent to the main mix with this control
turned fully counter-clockwise.
PMX1000: The
FX TO MAIN
control performs the same
function as on the PMX3000 and PMX5000
.
2.4 Main and monitor section
The
SURROUND
control determines the
effect intensity. This is a built-in effect, which
widens the stereo panorama, thus making
the sound more lively and transparent.
Press the
XPQ TO MAIN
switch to activate this effect.
Pressing the
AFL
switch (after-fader listening) activates
the solo function. If AFL is on for the corresponding channel
in the main section, you will only hear the signal from this
channel. Its volume can be adjusted with the fader.
Switching AFL on has no effect on the main or monitor mix,
as long as you dont move the fader. In this way, you can
monitor one or several selected signals via the PHONES/
CTRL jack
. When AFL is on, the corresponding control
LED illuminates.
+
The PMX1000 does not have an AFL function.
PMX1000:
FX SEND
fader
.
PMX3000:
FX
fader.
PMX5000:
FX 1/2
fader.
This is the master send fader for the signal routed to the
effects processor and to the FX SEND output
(see
also
and
).
PMX1000:
MON SEND
fader
.
PMX3000/PMX5000:
MON1/2 fader.
These faders are used to set the monitor output volume
(see also
and
).
PMX1000: The main mix allows you to control the volume
from the Main 1 output with both faders.
PMX3000/PMX5000: The
MAIN 1
fader controls the volume
of the EUROPOWER. The main signal is also provided at the
MAIN 1 output (see also
).
PMX3000/PMX5000: The
MONO
fader controls the mono
mix signal (see also
).
All manuals and user guides at all-guides.com
all-guides.com
