Behringer Eurodesk SX2442FX, Руководство пользователя

Страница: 11 / 20

11
EURODESK SX3242FX/SX2442FX User Manual
(51)
These are the master AUX SEND controls 1 and 2 for adjusting the volume
level sent to the corresponding aux send connectors (see
(52)
). This way,
you can control the mix of all AUX 1 or AUX 2 signals of the input channels.
The AUX SEND section also has a SOLO switch.
(52)
Fig. 2.23: Master aux send outputs
(52)
Use the AUX SEND outputs 1 and 2 to take the master AUX SEND
signals and route them to an external effects device or your monitor
speakers. Subsequently, you can return the effect signal, e.g. via the
STEREO FX RETURN inputs (see
(67)
) or specific input channels.
2.9 Graphic 9-band stereo equalizer
(53) (56)
(54) (55)
Fig. 2.24: The graphic stereo equalizer
(53)
Your EURODESK is equipped with a graphic 9-band stereo equalizer
processing either the main or the AUX 1 signal. Use the EQ to adapt the
sound to the room acoustics.
(54)
Use the
EQ IN
switch to switch the equalizer on. In this case, the fader
LEDs illuminate.
(55)
With the MAIN/AUX 1 switch you can determine the signal to be processed,
either main or AUX 1.
(56)
Press the
FBQ IN
switch to activate the FBQ Feedback Detection System.
The frequencies causing feedback are indicated by the brightly lit fader
LEDs, while all other LEDs are darker. Simply lower the level of the brightly
lit faders until feedback disappears.
◊
When the switch is in the “AUX 1” position (see
(55)
), the EQ fader
LEDs show both the MAIN and the AUX 1 signal simultaneously.
However, if feedback occurs in one of the signals, those signals without
feedback will be faded out to enable clear identification of where
feedback is occurring. If the MAIN signal happens to be the one carrying
feedback, put the switch
(55)
to “MAIN” and then use the 9-band EQ to
remove the feedback.
2.10 Effects section
(62) (64)
(65)
(63)
(57)
(58)
(59)
(61)
(60)
Fig. 2.25: The digital effects processor
(57)
Here you will find a list of all multi-effects presets (see also chapter 3
“Digital effects processor”).
(58)
The FX LED level meters show the effects processor’s input signal.
Be sure that the clip LED only illuminates with signal peaks. If it is lit
all the time, the effects processor is overloading and hence producing
unpleasant distortion.
(59)
The Effect displays show the currently selected presets.
(60)
This is the master
FX 1
(or 2) SEND control for adjusting the volume of all
FX send signals at the corresponding FX send jacks (see
(66)
) and at the
inputs of the built-in effects processor. Use it to control the master signal of
all FX 1/FX 2 signals from the input channels. When neither of the FX SEND
controls is turned up, the effects processor will not receive a signal.
(61)
Turn the FX 1 (or FX 2 ) control to select an effects preset. Then, push it
briefly to confirm your selection and activate the new effect.
(62)
The
FX 1
(or 2) TO
AUX 1
controls allow you to add the effect signal from
the built-in effects processor (FX1 or FX2) to the AUX 1 monitor signal.
Naturally, the effects processor must be provided with an input signal
(i.e. the FX controls in the channel strips plus the FX SEND controls and the
channel faders must be turned up).
(63)
This is the FX 1 (or 2) TO AUX 2 control adding the effect signal from the
effects processor to the AUX 2 monitor signal. See
(62)
for further details.
(64)
The
FX 1
(or 2)
TO MAIN
control routes the effect signal either to the main
mix or the subgroups 1 and 2 (or 3 and 4), depending on the position of the
selector switch (see
(65)
). When it is hard left, no effect signal will be audible.
Here, too, the FX controls in the channel strips plus the FX SEND controls and
the channel faders must be turned up.