Behringer Eurodesk SX2442FX, Руководство пользователя

Страница: 10 / 20

10
EURODESK SX3242FX/SX2442FX User Manual
(40)
The SOLO/PFL switch determines whether the monitored signal is pre
(PFL) or post-fader (SOLO) after pressing the SOLO/PFL switch (the LED
illuminates). The level meter indicates the corresponding signal (see
(39)
).
When you adjust a signal with the GAIN control, it is advisable to select PFL
mode, so that the level shown is independent of the channel fader position.
2.6.1 Talkback
The talkback function of the EURODESK allows you to communicate with
the musicians in the recording room or on the stage. The talkback signal
is present at the AUX SEND outputs, which are particularly useful for
monitor/ headphone mixes.
(42)
(41)
(43)
Fig. 2.17: Talkback section
(41)
The
LEVEL
control determines the volume of the talkback signal at the
AUX 1/2 outputs.
(42)
Use the TALK TO AUX 1/2 switch to activate the built-in talkback
microphone. Its signal is sent to the AUX SEND jacks 1 and 2. Keep the
switch pressed while you’re speaking.
(43)
This is the built-in talkback microphone.
2.6.2 Phones & control room
(44)
(43)
Fig. 2.18: Phones/control room section
(44)
The
PHONES/CTRL R
control adjusts the volume of the headphones
connected to the PHONES/ CTRL ROOM OUT jack (see
(46)
). If you have an
active monitor speaker or power amp connected here, you can also control
the monitor volume.
(45)
These switches select the signal sent to the PHONES/ CTRL ROOM jack.
Available sources are: MAIN, CD/TAPE, AUX 1/2 and subgroups 1 - 2 and 3 - 4.
(46)
Fig. 2.19: Phones/control room output
(46)
Connect your headphones or monitor speaker to the PHONES/CTRL
ROOM OUT ¼" TRS connector.
◊
IMPORTANT! High volume levels may damage your hearing and/or
your headphones/loudspeakers. To avoid switch-on/off thumps from
the console and any downstream devices, always make sure that the
power amp(s) or active speaker(s) are the last components that are
switched on and the first to be switched off. Always make sure that the
appropriate volume is set.
2.7 CD/Tape
(44)
(48)
Fig. 2.20: CD/tape
(47)
TO MAIN controls the volume of, for example, a CD player connected to the
CD/tape input connectors (see
(49)
).
(48)
When the
STANDBY
switch is pressed, all input channels are muted. Only the
CD/tape signal will be routed to the main mix. In this way, you can prevent
the microphones from pickung up unwanted sounds or noise that would
interfere with CD playback during a break. The main mix and channel faders
can remain in their normal positions while playing back music from CD
(using the CD/ TAPE INPUTs
(49)
), so you don’t lose your mix.
(50) (49)
Fig. 2.21: CD/tape connectors
(49)
The
CD/TAPE INPUT RCA
connectors are for the connection of CD players,
tape decks or other line-level sources. The signal volume is adjusted with
the TO MAIN control.
(50)
The CD/TAPE OUTPUT RCA connectors provide the stereo main mix signal to
a tape deck or DAT recorder to record your mix. The signal is taken pre-fader,
so that it will not be influenced by the fader positions.
2.8 Master Aux Send 1 and 2
(51)
Fig. 2.22: Master aux sends