background image

FEDERAL COMMUNICATIONS 
COMMISSION COMPLIANCE 
INFORMATION

Responsible party name: 

MUSIC Group Services USA, Inc.

Address: 

18912 North Creek Parkway, 

Suite 200 Bothell, WA 98011, 

USA

Phone/Fax No.: 

Phone: +1 425 672 0816 

Fax: +1 425 673 7647

B-CONTROL DEEJAY BCD2000

complies with the FCC rules as mentioned in the following paragraph:

This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to part 15 of the FCC Rules. These limits are designed 
to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause 
harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined 
by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and receiver.

• 

Connect the equipment into an outlet on a circuit different from that to which the 

• 

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

• 

This device complies with Part 15 of the FCC rules. Operation is subject to the 
following two conditions:

(1) this device may not cause harmful interference, and  
(2) this device must accept any interference received, including interference that may 
cause undesired operation.

Important information:

Changes or modifications to the equipment not expressly approved by MUSIC Group 
can void the user’s authority to use the equipment.

B-CONTROL DEEJAY BCD2000

Downloaded from 

ManualsNet.com

 search engine

Содержание B-CONTROL DEEJAY BCD200


















Отзывы: