background image

Other than the limited warranty extended hereby there is no other expressed
warranty in connection with the design, safety or use of any of the Company’s
products except as to title.

 

All implied warranties are expressly disclaimed

pursuant to the terms of this warranty.
3. CUSTOM WORK

If the Machine is used for commercial purposes such as custom work, the period
warranted for the Machine is limited to six (6) months from the date of delivery to the
first registered owner and does not cover any labor charges incurred.

4. RENTAL

If the Machine is used for rental purposes the period warranted for the Machine is
limited to thirty (30) days from the date of delivery to the first registered owner and does
not cover any labor charges incurred.

5. REGISTRATION

In order to qualify for coverage on this limited warranty, the product and name of the
original purchaser must be registered with the Company by a completed Machine
Pre-Delivery Checklist and Warranty Registration along with a copy of the dealer’s
invoice to the first registered owner to the Company within fourteen (14) days after the
date of delivery to the original purchaser.

6. WARRANTY SERVICE

Warranty Service must be performed by a dealer authorized by BEFCO. If the warranty
service requested is approved, the owner shall pay only for labor beyond the rate
allowed, for overtime labor, and for any mileage charge for transporting the equipment
to and from the dealer’s shop. It is assumed that the dealer has the appropriate general
and special tools to service the Machine. Time required for replacement of knives, oil,
grease and to remove excessive dirt from the Machine is not subject to reimbursement
by the Company. The owner is required to clean the Machine before presenting it to the
dealer for service work. The Machine must be delivered within thirty (30) days after
failure date by the owner to the dealer to be eligible for warranty consideration.

7. UNAPPROVED SERVICE OR MODIFICATION

All obligations of the Company under this limited warranty shall be terminated if:

a. Proper service and operation instructions as outlined in the Operator’s Manual

and on the instruction sticker on the Machine, are not followed.

b. The Machine is modified or altered in any way not approved by the Company.
c. The Company does not receive a copy of the dealers invoice to the first

registered owner within fourteen (14) days from the date of delivery.

d. The Company has not been paid in full, by the dealer, for the Machine.

8. ACCIDENTS AND NORMAL MAINTENANCE

This limited warranty covers defective material and workmanship. It does not cover
depreciation or damage caused by normal wear, accidents, improper maintenance,
improper protection or improper use. The costs of normal maintenance or repairs for
accidents or improper use, and related labor will be borne by the owner.

9. REPLACEMENT PARTS

BEFCO, Inc. warrants replacement parts to be free from defect in material and
workmanship for a period of thirty (30) days from the date of delivery to the original
purchaser.

W

ARRANTY

36

BEFCO

T

ILL

-R

ITE

 T60

O

PERATOR

S

 M

ANUAL

Содержание TILL-RITE T60-266





















































Отзывы: