Bee Robotics RB01 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 64

background image

BRDoc209

RoboBlot - User Manual [en-GB]

Rev: 2 | CRF: 2665

Bee Robotics Ltd

CONFIDENTIAL

Pg. 26 of 64

To complete the action of loading the Tip Rack, place your 1ml tips inside the holder, from
left to right. It’s advised that you load a full rack of 96 tips, but it’s required that you at-least fill
the positions that were outlined in the tip rack configuration menu on the software.

On the right-hand side of the holder, you will find 6x 5ML tip holders. You should load the
appropriate amount of 5ML tips. Note that the instrument picks these up in column-wise order,
starting from top left and working down. The instrument will always start picking 5ML tips from
the top left.

With the tips inserted, place the holder onto the mounting points on the deck. You may refer to
Section 4.2 for location details.

Check off the action on-screen when done.

To complete the action of loading the tray, place the disposable tray onto the appropriate
tray holder and secure firmly on-top of the tray table inside the instrument (using the clamps if
applicable).

Check off the action on-screen when done.

«
...
24
25
26
27
28
...
»

Содержание RB01

































































Отзывы:

Нет отзывов

Похожие инструкции для RB01

Бренд: iGuzzini Страницы: 20

WJHD309 - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 7

WJ-ND300 Administrator Console

Бренд: Panasonic Страницы: 24

Бренд: AccuMed Страницы: 14

Бренд: TAS Страницы: 25

Бренд: Parker Страницы: 39

Бренд: B medical systems Страницы: 28

Бренд: Haaga Страницы: 31

Бренд: Hach Страницы: 66

Бренд: Hach Страницы: 14

Бренд: Hach Страницы: 144

QuikChem 8500 2 Series

Бренд: Hach Страницы: 80

Бренд: Hach Страницы: 178

Бренд: Hach Страницы: 32

Бренд: hager Страницы: 4

SimMan 3G Trauma

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды