Bedrock UPS.500 Скачать руководство пользователя | Manualshive

Страница: 21 / 54

background image

Chapter 3

9/2/21

Bedrock UPS.500 User Manual - BRDOC120_008

20

UPS.500 Wiring

Important User

Information

Be sure to observe the following when working with the UPS.500.

CAUTION:

Always use an appropriate fuse on the power in and

power out connections.

CAUTION:

The UPS.500 contains lithium

-

ion batteries. The

output port may carry voltage even when the UPS.500 is not
connected to a power source.

CAUTION:

Never attempt to open the UPS.500 enclosure. The

enclosure is securely sealed. Opening the enclosure will void
the warranty and cause the UPS.500 to be inoperable.

NOTE:

The UPS.500 contains lithium

-

ion batteries. The product

is not field

-

serviceable. Contact Bedrock Automation for

instructions on returning the UPS.500.

Power and Relay

Cables

Wire labels for the power in, power out, and relay cables for the UPS.500 are

illustrated in Figure 3

NOTE:

For all cables, connect the drain wire to panel ground.

Important:

Power cabling must be rated for PLTC with AWG 16.
Relay cabling must be rated for MC, MV, or PLTC with AWG 20.

CAUTION:

See the UPS.500 Specifications (Appendix A) for

relay contact rating information.

«
...
19
20
21
22
23
...
»

Содержание UPS.500























































Отзывы:

Нет отзывов

Похожие инструкции для UPS.500

Бренд: CAMAG Страницы: 40

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: IDEAL Networks Страницы: 60

Бренд: IceCure Страницы: 104

Бренд: laerdal Страницы: 8

Бренд: LAHTI PRO Страницы: 16

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 8

Бренд: M-Audio Страницы: 3

Бренд: Valcom Страницы: 6

Бренд: Vaisala Страницы: 60

Бренд: Vaisala Страницы: 146

Бренд: Waters Страницы: 250

Бренд: Waters Страницы: 141

Бренд: Additel Страницы: 107

Бренд: Varimixer Страницы: 28

REBOUND DUAL ST

Бренд: Össur Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды