Bedrock SM50 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 39

Bedrock SM50 Скачать руководство пользователя страница 21

20

Bedrock SM50 operating manual

© Embedded Acoustics BV, 2015

21

Settings

The settings module allows you to configure the generic settings of the device, in addition
to the module-specific settings found in each module. The following attributes can be set:

•

Time and date (time in 24h format and date in DD-MM-YYY format)

•

Time interval before the backlight automatically switches off to save power

•

Brightness of the display (

only on specific versions of the SM50

)

•

Phantom power to the microphone

•

Microphone pre-amplifier gain

•

Calibration of the touch screen digitizer

The system date and time are changed by means of the arrows (up/down). Note that your
changes are not applied until you press “set clock.”

Date and time in the settings module

The SM50 has an internal real-time clock that keeps running even when the device is
powered off. The clock needs to be adjusted if the battery has been depleted completely, for
instance when the device has not been used for a very long time. The system date and time
are used for time-stamping the saved data. If you download measurement data over USB,
the file creation date/time are only accurate if the internal real-time clock of the SM50 was
updated to the right date and time.

Press the “calibrate touch” button if the response of the touch screen appears to be inac-
curate. Calibration takes place by pressing exactly on the indicated marks near the corners
of the screen.

We strongly recommend that you use a stylus for calibration, to obtain cali-
bration settings that are as accurate as possible. Not that false responses dur-
ing the calibration procedure (tapping completely in the wrong place) may
render the touch screen unusable.

«
...
19
20
21
22
23
...
»

Содержание SM50








































Отзывы:

Нет отзывов