Bedder Way ECONOMY MELAMINE MURPHY BED Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 30

Bedder Way ECONOMY MELAMINE MURPHY BED Скачать руководство пользователя страница 4

4 of 30

BEFORE YOU INSTALL YOUR MURPHY BED

1.

Unless you requested to have your Murphy bed without a notch for the base molding at
the bottom of your wall, a 5 inch tall by 1 inch notch is included on your Murphy bed

Cabinet Verticals.

This is necessary for the Murphy bed to sit flush against the

wall for a secure installation.

If you ordered your Murphy bed without a notch

because you want to make a different size notch, you should do this first, BEFORE any

other step.

Follow the steps below to make a notch/or make a larger notch for your base molding:

a.

Mark your notch height and notch depth on the inside of each side vertical.

Notches deeper than 1 ½” will interfere with the Stringer. If your notch size
needs to be deeper than 1 ½”, please go to Page

29 for further instructions.

Do this BEFORE installing your murphy bed.

b.

Using a handsaw or a jigsaw, make two straight line cuts based on your marks.

c.

Hold the side verticals up against the wall with the unfinished/notched side towards

the wall to double check that the notches you made will accommodate your wall’s

base molding.

Notches

are not to exceed 12” High x 2” Wide.

«
...
2
3
4
5
6
...
»

Содержание ECONOMY MELAMINE MURPHY BED































Отзывы:

Нет отзывов