Beckhoff CX20 2 Series Скачать руководство пользователя страница 65

Страница: 65 / 77

Decommissioning

CX20x2

Version: 1.7

Decommissioning

11.1

Removing cables

NOTE

Electrical voltage

If the power supply is switched on during dismounting, this can lead to damage to the Embedded PCs.

• Switch off the power supply for the Embedded PCs during dismounting.

Cabling

Make a note of the wiring configuration, if you wish to restore it with another device.

Before dismantling the Embedded PC, shut down the Embedded PC and switch off the power supply. Only
then can you remove all the cables. Also remove all cables from the first terminal after the power supply
terminal.

Requirements:

• Exit the software and shut down the Embedded PC.

• Switch off the power supply.

Remove the cables as follows:

1. Remove the wiring from the basic CPU module, any system interfaces that may be connected and the

extension modules.

2. Remove the wiring from the first terminal next to the power supply terminal.

3. Pull the orange strap to remove the first terminal after the power supply terminal by pulling it forward.

In the next step the Embedded PC can be removed from the DIN rail and dismantled.

Содержание CX20 2 Series














































































Результаты поиска

Содержание CX20 2 Series

Отзывы:

Похожие инструкции для CX20 2 Series

Бренды по названию

Популярные бренды

Beckhoff CX20 2 Series, Руководство пользователя

Результаты поиска

Содержание CX20 2 Series

Отзывы:

Похожие инструкции для CX20 2 Series

Бренды по названию

Популярные бренды