Beckhoff CX20 2 Series Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 77

background image

Commissioning

CX20x2

36

Version: 1.7

6.2.6

Installing passive EtherCAT Terminals

Incorrectly installed passive EtherCAT Terminals

The E-bus signal between an Embedded PC and the EtherCAT Terminals can be impaired due to
incorrectly installed passive EtherCAT Terminals.

Passive EtherCAT Terminals should not be installed directly on the power supply unit.

EtherCAT Terminals that do not take part in active data exchange are referred to as passive terminals.
Passive EtherCAT Terminals have no process image and do not require current from the terminal bus (E-
bus).

Passive EtherCAT Terminals (e.g. EL9195) can be detected in TwinCAT. In the tree structure the EtherCAT
Terminal is displayed without process image, and the value in column “E-bus (mA)” does not change,
compared to the preceding EtherCAT Terminal.

Fig. 25: Identifying a passive EtherCAT Terminal in TwinCAT.

The entry "Current consumption via E-Bus" in the technical data of an EtherCAT Terminal indicates whether
a particular EtherCAT Terminal requires power from the terminal bus (E-bus).

The following diagram shows the permissible installation of a passive EtherCAT Terminal. The passive
EtherCAT Terminal was not directly attached to the power supply unit.

Fig. 26: Passive EtherCAT Terminals, permissible installation.

The following diagram shows the invalid installation of a passive EtherCAT Terminal.

Fig. 27: Passive EtherCAT Terminals, invalid installation.

«
...
34
35
36
37
38
...
»

Содержание CX20 2 Series














































































Отзывы:

Нет отзывов

Похожие инструкции для CX20 2 Series

Бренд: Gateway Страницы: 124

Бренд: XtendLan Страницы: 17

ECS-9755-505MGTX950

Бренд: Vecow Страницы: 111

Бренд: VISIONARY DESIGNS Страницы: 2

Бренд: Gateway Страницы: 108

ProArt PA Series

Бренд: Asus Страницы: 40

Бренд: Asus Страницы: 46

Бренд: Asus Страницы: 80

Бренд: Asus Страницы: 76

Бренд: Asus Страницы: 75

Бренд: Asus Страницы: 44

Бренд: Asus Страницы: 90

Бренд: Asus Страницы: 56

P5G43 V4-Series

Бренд: Asus Страницы: 110

Бренд: Asus Страницы: 44

Бренд: Asus Страницы: 56

Бренд: Asus Страницы: 44

Бренд: Asus Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды