background image

Foreword 

 

 

1.2   Safety instructions 

1.2.1  State at Delivery 

All the components are supplied in particular hardware and software configurations appropriate for the 
application. Modifications to hardware or software configurations other than those described in the 
documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH. 

1.2.2  Operator’s obligation to exercise diligence 

The operator must ensure that 

• 

the product is only used as intended (see chapter 

Product Description

• 

the product is in a sound condition and in working order during operation (see  chapter 

Maintenance

• 

the product is operated, maintained and repaired only by suitably qualified and authorized 
personnel 

• 

the personnel is instructed regularly about relevant occupational safety and environmental 
protection aspects, and is familiar with the operating manual and in particular the safety notes 
contained herein 

• 

the operation manual is in good condition and complete, and always available for reference at the 
location of the product 

• 

none of the safety and warning notes attached to product are removed, and that all notes remain 
legible. 

1.3  Description of safety symbols 

The following safety symbols are used in this operating manual. They are intended to alert the reader to 
the associated safety instructions. 

Acute risk of injury! 

 

DANGER 

If you 

do not

 adhere the safety advise adjoining this symbol, there is immediate 

danger to life and health of individuals! 

 

Risk of injury! 

 

WARNING 

If you 

do not

 adhere the safety advise adjoining this symbol, there is danger to life and 

health of individuals! 

 

Hazard to individuals! 

 

CAUTION 

If you 

do not

 adhere the safety advise adjoining this symbol, there is obvious hazard to 

individuals! 

 

Hazard to devices and environment 

 

Attention 

If you 

do not

 adhere the notice adjoining this symbol, there is obvious hazard to 

materials and environment. 

 

Note or pointer 

 

Note 

This symbol indicates information that contributes to better understanding. 

4

 

CU8005-0000 

Содержание CU8005-0000



















Отзывы: