background image

4

4 INCH CHIPPER

SAFETY

1.7 SAFETY DECALS

Keep hands and feet out of inlet and discharge 

openings while machine is operating to avoid serious 

personal injury. Stop and allow machine to come to a 

complete stop before clearing obstructions.

Read and understand this owner/operators 

manual. Be completely familiar with the 

controls and the proper use of this equipment
Obtain and wear safety glasses and use 

hearing protection at all times when operating 

this machine.
Before inspecting or servicing any part of this 

machine, shut off power source, remove the 

key, disconnect spark plug wire from spark 

plug and make sure all moving parts have 

come to a complete stop.

Do not operate this equipment in the 

vicinity of bystanders. Do not allow children 

to operate this equipment. Always stand 

clear of discharge area when operating 

this machine. Keep face and body away from discharge areas.

Do not operate machine without shields in place. 

Failure to do so may cause serious injury or death.

Check blade bolts for proper torque 

after every 8 hours of operation. 

Check blades and rotate or 

resharpen daily or as required to 

keep blades sharp. Refer to owners 

manual for instructions. Failure to do so may cause poor performance, 

damage or personal injury and will void the machine warranty.

Read and understand you owners manual before operating. If owners 

manual was not included or you have any questions, please call 

800.247.7335 or 701.282.5520 (U.S.A.).

See Section 1.8 for decal locations. Familiarize yourself with all of the safety and operating decals on the machine 

and the associated hazards. See the engine owner's manual or contact the engine manufacturer for engine safety 

instructions and decals.

Keep hands and feet out of inlet and 

discharge openings while machine is 

operating to avoid serious personal injury. 

Stop and allow machine to come to a complete stop before clearing 

obstructions.

454

1000

5.30-12

550 kPa, 80 psi

1

6

2

7

3

4

8

5

PN 12169

PN 12172

PN 12173

PN 12174

PN 12175

PN 14942-00

PN 12250

PN 32161-00

Operation of this equipment may create 

sparks  that  can  start  fires  around  dry 

vegetation. A spark arrestor may be 

required. The operator should contact 

local fire agencies for laws or regulations 

relating to fire prevention requirements.  

9

PN 33883-00

33883-00

WARNING

ADVERTENCIA

OPERATION OF THIS EQUIPMENT MAY CREATE SPARKS 

THAT CAN START FIRES AROUND DRY VEGETATION. A 

SPARK ARRESTOR MAY BE REQUIRED. THE OPERATOR 

SHOULD CONTACT LOCAL FIRE AGENCIES FOR LAWS 

OR REGULATIONS RELATING TO FIRE PREVENTION 

REQUIREMENTS.  

EL USO DE ESTE EQUIPO PUEDE CREAR CHISPAS 

CAPACES DE INICIAR INCENDIOS EN VEGETACION 

SECA. PODRIA SE NECESARIO USAR UN PARACHISPAS. 

EL OPERADOR DEBERA COMUNICARSE CON CUERPOS 

DE BOMBEROS LOCALES PARA INFORMARSE DE LEYES 

O REGLAMENTOS RELACIONADOS CON LOS 

REQUISITOS EXIGIDOS PARA LA PREVENCION DE 

INCENDIOS.  

Содержание CH4420

































Отзывы: