Beamz 150.379 Скачать руководство пользователя страница 20

 

20 

DEBALLAGE 

ATTENTION !

 Immédiatement après réception, vérifiez le contenu du carton et assurez-vous que tous les éléments sont bien 

présents et en bon état. Si besoin, faites les réserves nécessaires si le matériel ou les cartons sont endommagés. SI l’appareil 
doit être retourné, faites-le dans l’emballage d’origine.  
 
Si l’appareil a été exposé à des fluctuations importantes de températures (par exemple après le transport), ne l’allumez pas 
immédiatement. De la condensation peut survenir. Laissez l’appareil éteint le temps qu’il atteigne la température ambiante. 
 

ALIMENTATION 

Vous trouvez sur l’étiquette à l’arrière de l’appareil, le type d’alimentation à utiliser. Vérifiez que la tension d’alimentation 
corresponde à celle mentionnée. Toute autre alimentation peut endommager l’appareil. Reliez l’appareil au secteur, il est prêt à 
être utilisé. En aucun cas, vous ne devez utiliser de dimmer ou d’alimentation réglable. 

 

Connectez toujours l'appareil à un circuit protégé (disjoncteur ou fusible). Assurezvous que l'appareil soit correctement 
relié à la terre afin d'éviter tout risque d'électrocution ou d'incendie. 
 

INSTALLATION 

 

 

 

Attention: 

 

L’installation de l’appareil doit être pensée et réalisée de telle sorte que le support de fixation puisse supporter 10 fois 
le poids de l’appareil pendant une heure sans aucune déformation. 

 

L’installation doit toujours être assurée par un second système de fixation, par exemple un filet ou une élingue. Ce 
second système doit être conçu de telle sorte que aucun élément de l’installation ne puisse tomber si la fixation 
principale venait à rompre. 

 

Assurez-vous que la zone sous l’emplacement de montage ne puisse pas accueillir de public pendant le montage, le 
démontage et l’utilisation.  

 

Le responsable du fonctionnement doit faire approuver par un expert les conditions d’installation et d’utilisation de 
l’appareil avant la première mise en service et après tout changement. 

 

Le responsable du fonctionnement doit faire approuver par un expert les conditions d’installation et d’utilisation de 
l’appareil, une fois par an. 

 

L’appareil doit être installé de telle sorte que personne ne puisse l’atteindre, passer dessous ou être assis. 

 

 

 

 

 

 

 

 

 

ATTENTION : 

Lors de l’installation, tenez compte des normes nationales 

respectives ! Seuls des revendeurs et installateurs habilités 
peuvent procéder à l’installation.

  

ATTENTION :   

Lorsque vous installez l’appareil, assurez-vous qu’il n’y a aucun 

matériau fortement inflammable (décorations par exemple) à 0,5 
mètres au moins de l’appareil. 

Содержание 150.379

































Отзывы: