manualshive.com logo in svg

BEA LZR P110, Руководство пользователя, Страница: 18 / 20

Поделиться
Скачать
BEA LZR P110 Скачать руководство пользователя страница 18

18

1

1

1

1

1

2
3

1
2

3

1

1

1

1

1

1

1

1

1

2

1

1

1

1
2

TROUBLESHOOTING

No blue LED

Only the blue LED 

is on.

The detection LED 

remains green.

The orange LED is 

flashing and the 

detection LEDs are 

red. 

The detection LED 

remains red.

The orange LED 

is on.

The sensor does 

not respond to the 

remote control.

The sensor does not 

unlock.

There is no power.

The test input is not 

connected.

The detection field is too 

small or deactivated.

Someone or something is 

in the detection field.

The field is touching the 

floor, the wall or the door, 

which leads to detection.

No background (reference 

point) is found.

The sensor is masked.

The power supply voltage is 

exceeding the acceptable limits.

The sensor exceeds its 

temperature limits.

Internal error

4 hours after last use of the 

remote control, the sensor 

locks the access to the remote 

control session.
The batteries in the remote 

control are not installed 

properly or dead.

The remote control is badly 

pointed. 

A reflective object is in close 

proximity to the sensor.

You have to enter an access 

code or the wrong code was 

entered. 

The object size is too small.

The polarity of the power 

supply is inverted.

Check cable and connexion.

Check wiring.

The RED and BLUE cable have to be connected 

to the test input or the power supply.

Check the size of the fields.
Launch a teach-in.

Step out of the field and/or remove the any 

object(s) from the field.

Activate the 3 red beams and check if the 

position of the sensor is correct. 

If not, adjust the hex screws.
Verify the field size.
Launch a teach-in.

Check the position of the sensor.

Check the mounting side setting.

If there is no background, set the mounting side 

to value 3 to 5.

Launch a new teach-in.

Verify and clean the front screens with a damp cloth.

Check the power supply voltage.

Verify the outside temperature where the sensor 

is installed. Eventually protect the sensor from 

sunlight using a cover.

Wait a few seconds. 

If the LED remains ON, reset the power supply. 

If the LED turns on again, replace the sensor.

Cut and restore power supply. 

The remote control session is accessible again 

during 4 hours. 

Verify or replace the batteries.

Point the remote control towards the sensor, but 

with a slight angle. 

Avoid highly reflective material in proximity to 

the sensor.

Cut and restore power supply. 

No code is required to unlock during the first 

minute after powering.

Check the polarity of the power supply.

Decrease the min. object size.

All LEDs have been de-

activated by remote control.

Activate the LEDs by remote control.

The virtual push 

button does not 

work.

The position of the sensor 

has been changed.

Check the position of the sensor.
Launch a new VPB teach-in.

Содержание LZR P110





















Отзывы:

Нет отзывов