Page 4 of 5
75.5892.03 KEYPADS 20171013
Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462 | General Tech Questions: [email protected] | Tech Docs: www.BEAinc.com
Page 4 of 5
75.5892.03 KEYPADS 20171013
6 Keypad Programming (cont.)
red
red
red flashing
red flashing
DOOR MODE
green
green
3a) Set unlocking time for zone 1:
a. Enter “setup” mode.
b. Press the star (*) key and then “1”. Mode LED will flash red.
c. Enter a 2-digit number (00
–
99) for the “unlock time” value.
• “00” = sets “unlock time” to toggle mode (“00” to both open and close the door)
• “01”
–
“99” = “unlock time” in seconds
d. After entering the “unlock time” number, a long beep will sound and the mode LED turns red.
e. Press “#” again to exit “setup” mode. Mode LED turns green.
3b) Set unlocking time for zone 2:
a. Enter “setup” mode.
b. Press the star (*) key and then “5”. Mode LED will flash red.
c. Enter a 2-digit number (00
–
99) for the “unlock time” value.
• “00” = sets “unlock time” to toggle mode (“00” to both open and close the door)
• “01”
–
“99” = “unlock time” in seconds
d. After entering the “unlock time” number, a long beep will sound and the mode LED turns red.
e. Press “#” again to exit “setup” mode. Mode LED turns green.
(when zone 1 relay is active)
(when zone 2 relay is active)
red
red
red
red
red
red
red flashing
red flashing
green
green
green
green
green
red
2a) Add user code to zone 1:
This code must be different from the admin code.
a. Enter “setup” mode.
b. Press the star (*) key and then “9”. Mode LED will flash red.
c. Press “0” and then “2”. A short beep will sound. Mode LED will turn red.
d. Enter a 3-digit number (000
–
999) to set the electronic location for the zone 1 user code. LED remains red,
and a a short beep will sound after entering the 3-digit number.
e. Enter the new user code.
The user code must be the same length as the admin code.
A long beep will sound.
User code is successfully added.
The new code will replace the existing code stored in the same location.
f. Repeat the previous two steps to add more codes.
g. Press “#” to exit “Add user code to zone 1” mode. Mode LED remains red.
h. Press “#” again to exit “setup” mode. Mode LED turns green.
NOTE: When zone 1 output relay is activated, the door indicator LED will turn green.
2b) Add user code to zone 2:
This code must be different from the admin code and the user code for zone 1.
a. Enter “setup” mode.
b. Press the star (*) key and then “9”. Mode LED will flash red.
c. Press “0” and then “3”. A short beep will sound. Mode LED will turn red.
d. Enter a 2-digit number (00
–
99) to set the electronic location for the zone 2 user code. LED remains red, and a
a short beep will sound after entering the 2-digit number.
e. Enter the new user code.
The user code must be the same length as the admin code.
A long beep will sound.
User code is successfully added.
The new code will replace the existing code stored in the same location.
f. Repeat the previous two steps to add more codes.
g. Press “#” to exit “Add user code to zone 2” mode. Mode LED remains red.
h. Press # again to exit “setup” mode. Mode LED turns green.
NOTE: When zone 2 output relay is activated, the door indicator LED will turn red.
