BDI SEMBLANCE Скачать руководство пользователя страница 20

PB

20

Helpful Tips for Designing your own Semblance Package.

The Cabinet Bracket Screw must be 1 

space hole above the Shelf Screw to 

align Cabinet bottom with the top of a 

Shelf.

There is a 7 insert spacing pattern to 

align Shelves with top and bottom of a 

Cabinet.

There is a 3 insert spacing pattern, from 

Cabinet Bracket to Shelf Frame, to 

align Shelves with middle of a Cabinet.

ADJUST DOOR HINGES (IF NEEDED)

If the cabinet’s door appears out of alignment, this can be corrected with 

minor adjustment on each door. 
Because these hinges are infinitely adjustable, adjusting one hinge element 

can sometimes cause the need for adjustments to other elements. But with 

a few adjustments, you can modify the orientation of the cabinet door to 

make sure that it hangs evenly.
Use a Phillips screwdriver to adjust cabinet’s door hinges: 

• 

By adjusting Screw 1, the door will move LEFT or RIGHT within the  

 

frame. Make minor adjustments at both top and bottom hinges for   

 

best results. 

• 

By adjusting Screw(s) 2, the door will move UP or DOWN within   

 

the frame (the top and bottom hinges must be adjusted the same   

 

degree).

NOTE: Loosen Screws 2 one complete turn, raise or lower door, then hold 

in position while tightening Screws 2 (on both hinges).

• 

By adjusting Screw 3 the entire door will move IN or OUT, opening   

 

or closing the gap between the doorframe and cabinet. (This screw  

 

rarely needs adjustment.) 

REVERSE DOOR-SWING (IF DESIRED)

The Single Cabinets feature a reversible door assembly so that you can 

open either from the left or the right. 

To reverse the door’s orientation, 

1.  Remove the Door by actuating both of its quick-release hinges (A);   

 

carefully place the detached Door aside. 

2.  Using a Philips head screwdriver, remove both Hinge Plates from   

 

the interior wall of the cabinet by loosening the screws holding it in  

 

place (B).

3.  Install both Hinge Plates to the opposite interior wall at the   

 

pre-determined locations. 

4.  Re-install the Door by connecting each Door Hinge to the relocated  

 

Hinge Plates. 

Designed by Matthew Weatherly. These distinctive product configurations are protected by US and international patents, trade dress, and/or copyright laws. 
BDI are trademarks of Becker Designed, Inc. All Rights reserved. ©2013, BDI Assembled in the US from parts of foreign origin. REV061413v2

7 inserts

CABINET

3 inserts

 

1.

2.

3.

3.

1.

*2.

*2.

 

A

B

B

CABINET

CABINET

Содержание SEMBLANCE





















Отзывы: