background image

BCM   BPR1000-PU/BPR1000-U/MOR600-N 

 
 

產品

:Mobile Router

 

根據交通部低功率管理辦法規定

第十二條

   

經型式認證合格之低功率射頻電機,非經許可、公司、商號或使用者均不得擅自變更頻率,加大功率或變更原設計之特性及功能。

 

第十四條

   

低功率射頻電機之使用不得影響飛航安全及干擾合法通信

:

經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。

 

前項合法通信,指依電信規定作業之無線電信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干

 

 

You are cautioned that changes or modifications not expressly approved by the party responsible for 
compliance could void your authority to operate the equipment.   
1.  This transmitter must not be co-located or operating in conjunction with any other antenna or 

transmitter. 

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled 

environment. This equipment should be installed and operated with a minimum distance of 20 
centimeters between the radiator and your body.   

"The antenna(s) used for this device must be installed to provide a separation distance of at least 20 cm 
from all persons and must not be co-located or operating in conjunction with any other antenna or 
transmitter."

 

 

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant 
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. 
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures: 
---Reorient or relocate the receiving antenna. 
---Increase the separation between the equipment and receiver. 
---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
---Consult the dealer or an experienced radio/TV technician for help. 
 

Содержание BPR1000 Series















Отзывы: