manualshive.com logo in svg

BCM Advanced Research SQ596, Руководство пользователя

Поделиться
Скачать
BCM Advanced Research SQ596 Скачать руководство пользователя страница 10

SQ596

6

Installation Steps

Jumper Settings

You can configure the hardware options by setting jumpers on the mainboard. A jumper is a
set of two or more metal pins in a plastic base attached to the mainboard. A plastic jumper
cap  with a metal(conductive) plates inside fits over two pins to create an electrical contact
or short between them. This contact establishes a hardware setting and is referred to as a

closed  jumper setting.

Some jumper have two pins while others may have three or more. Jumpers are sometimes
combined into sets called jumper blocks where all the jumpers in the block must be set
together to establish a hardware setting. In this manual the jumper settings will be described
graphically using a triangle ( )always marking pin 1. Those jumpers with two pins will be
shown as closed and open. A jumper is referred to as closed by placing the plastic jumper
cap over the two jumper pins and as open by removing the jumper cap. Some jumpers are
oriented vertically and other horizontally with pin 1 marked as (=P1).

Jumpers, Jumper caps, and Jumper blocks

Jumper

cap

2-pin

jumper

3-pin

jumper

4-pin

jumper

Jumper

block

Setting 3-pin jumpers

P 3   P 2   P 1

Jumper Pins 1 & 2 are closed with a jumper cap

P 3   P 2   P 1

Jumper Pins 2 & 3 are closed with a jumper cap

Setting 2-pin jumpers

Setting 2-pin jumpers

This jumper is closed with the jumper cap is placed over 2 pins

Содержание SQ596

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды