manualshive.com logo in svg

BCM Advanced Research MX852E-C10 Series, Руководство пользователя

Поделиться
Скачать
BCM Advanced Research MX852E-C10 Series Скачать руководство пользователя страница 100

MX855E/ MX852E-C10 Series 

100 MX855E/ MX852E-C10 Series User’s Manual

 

 

 

Overview 

During the Power On Self-Test (POST), if the BIOS detects an error requiring you to do 
something to fix, it will either sound a beep code or display a message. 
If a message is displayed, it will be accompanied by: 
PRESS F1 TO CONTINUE, CTRL-ALT-ESC OR DEL TO ENTER SETUP 
 

Post Beep 

Currently there are two kinds of beep codes in BIOS. This code indicates that a video error 
has occurred and the BIOS cannot initialize the video screen to display any additional 
information. This beep code consists of a single long beep followed by two short beeps.  
The other code indicates that your DRAM error has occurred. This beep code consists of a 
single long beep repeatedly. 
 

Error Messages 

One or more of the following messages may be displayed if the BIOS detects an error 
during the POST. This list includes messages for both the ISA and the EISA BIOS. 

1.  CMOS BATTERY HAS FAILED 

CMOS battery is no longer functional. It should be replaced. 

2.  CMOS CHECKSUM ERROR 

Checksum of CMOS is incorrect. This can indicate that CMOS has become corrupt.    This 
error may have been caused by a weak battery. Check the battery and replace if 
necessary. 

3.  DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER 

No boot device was found. This could mean that either a boot drive was not detected or the 
drive does not contain proper system boot files.  Insert a system disk into Drive A: and 
press <Enter>. If you assumed the system would boot from the hard drive, make sure the 
controller is inserted correctly and all cables are properly attached.    Also be sure the disk 
is formatted as a boot device.    Then reboot the system. 

4.  DISKETTE DRIVES OR TYPES MISMATCH ERROR - RUN SETUP 

Type of diskette drive installed in the system is different from the CMOS definition.    Run 
Setup to reconfigure the drive type correctly. 

Содержание MX852E-C10 Series



















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды