6
WWW.BBTA.COM.AU
BBT-BC-26CCBH, BBT-BC-26CCDH, BBT-BC-52CCBH
GENERAL SAFETY RULES
This machine can cause serious injuries. Read the
instructions carefully for the correct handling,
preparation, maintenance, starting and stopping of
the machine. Be familiar with all controls and the
proper operation of them. Know how to stop the
machine and disengage them quickly.
Keep this manual in a safe place for future and regular
reference and for ordering replacement parts.
Never allow children or anyone unable to fully
understand the directions given in the manual to use
the machine.
• Always wear safety goggles
for eye protection. Dress
properly; do not wear
loose clothing or jewellery
that could become caught
in the moving parts of
this unit. Safe, sturdy,
non-slip footwear should
always be worn. Long hair
should be tied back. It is
recommended that legs and
feet be covered to protect
from flying debris during
operation.
• Inspect the entire machine for loose parts (nuts,
bolts, screws, etc.) or any damage. Repair or replace
as necessary before using the machine.
• DO NOT use any attachment with this power
head other than the ones recommended by our
company, otherwise this could cause serious injury
to the operator or bystander, as well as damage to
the machine.
• Keep the handles free from oil and fuel.
• Always use proper handles and shoulder strap
when cutting.
• DO NOT smoke while mixing fuel or filling the tank.
• DO NOT mix fuel in an enclosed room or near open
flames. Ensure adequate ventilation.
• Always mix and store the fuel in an approved and
properly marked container that is approved by
local codes and ordinances for such usage.
• NEVER remove the fuel tank cap while the engine
is running.
• NEVER start or run the engine inside a closed
room or building. Fumes from the exhaust contain
dangerous carbon monoxide.
• NEVER attempt to make engine adjustments while
the unit is running and strapped to the operator.
Always make engine adjustments with the unit
resting on a flat, clear surface.
• DO NOT use the unit if it is damaged or poorly
adjusted. Never remove the machine’s guard.
This could cause serious injury to the operator or
bystanders as well as damage to the machine.
• Inspect the area to be cut and remove all debris
that could become tangled in the nylon cutting
head. Also remove any objects that the unit may
throw during cutting.
• Keep children away. Onlookers should be kept
at a safe distance from the work area, at least 15
metres.
• NEVER leave the machine unattended.
• DO NOT use this unit for any job other than those
for which it is intended and as described in this
manual.
• DO NOT over reach. Keep proper footing and
balance at all times.
• DO NOT run the unit while standing on a ladder or
on any other unstable footing location.
• Keep hands and feet clear of the nylon cutting
head while unit is in use.
• DO NOT use this type of machine for sweeping
away debris.
• DO NOT use the unit when you are tired, ill or under
the influence of medication, drugs or alcohol.
• Use nylon cutting head which is free of damage.
If a stone or any other object hits the machine,
stop the engine and check the nylon cutting head.
A broken or unbalanced nylon cutting head must
never be used.
Instructions for Changing Accessories
• DO NOT store in a closed area where fuel vapours
can reach an open flame from hot water heaters,
heaters, etc. Store in a locked, well ventilated area
only.
• To ensure safe and proper performance of
your product use only the parts available from
your dealer. The use of any other accessories or
attachments may cause a potential hazard or injury
to the user, damage to the machine and void this
warranty.
• Clean the machine completely, especially the fuel
tank, its surroundings, and the air filter.
• When refuelling, be sure to stop the engine and
confirm that it is cooled down. Never refuel when
the engine is running or hot. When fuel spills, be
sure to wipe it up completely and properly dispose
of those materials before starting the engine.
• Stay clear of other workers or bystanders by at
least 15 metres/50 feet.
• Whenever approaching the operator of the
machine, carefully call for their attention and
confirm that the operator has stopped the engine.
Be careful not to startle or distract the operator,
this can cause an unsafe situation.
• NEVER touch the nylon cutting head whenever the
engine is running. If it is necessary to adjust the
protector or nylon cutting head, be sure to stop
the engine and confirm that the nylon cutting
head has completely stopped running.
