Bayne Revolution HD 1999-0520 Скачать руководство пользователя страница 7

Страница: 7 / 52

Issued June 2017

Revision No: 001

Printed in U.S.A.
Copyright 2017, Bayne Premium Lift Systems

Specifications

SPECIFICATIONS

WI-0502-A

A. Rotary Actuator - rack and pinion style design.

Rack, pinion, and shaft bearings are constantly lubricated by the hydraulic oil for extended life.

Body and caps are made of high quality ductile iron.

Pinion output shaft and racks are made of high tensile alloy steel.

The rotary actuator provides smooth motion throughout the lift cycle, which results in longer cart life with virtually no
cart damage or abuse.

B. The lift unit measures only 7-5/8” thick from the rear of the mainframe to the outer most point of the lift saddle in the

down position. This allows for easy dumping of large commercial containers without interference.

C. The cart is normally rotated to 51 degrees and placed over 13” inside the truck opening in the dump position thus

reducing any potential spillage of materials.

D. The lift unit operates at a cycle time of 8 to 10 seconds for safe, fast, efficient service.

NOTICE

Cycle time is controlled by flow rate, as flow rate increases, cycle times decrease.

WARNING

Never operate faster than the cycle time listed above to avoid injury and maintain manufacturer’s warranty.

Recommended flow rate is

2 to 2 1/2 GPM

Hydraulic pressure requirements are as follows:

1800 PSI

normal working pressure

3000 PSI

maximum pressure

All lifters can be a bolt on type installation for easy, quick maintenance and less downtime.

Three ( 3 ) year limited warranty from date of delivery on all units and models when properly maintained and operated
within the recommended cycle time.

NOTICE

All lift units and parts are inspected by our Quality Control Department before shipment to guarantee the highest
performance and satisfaction.

For more information, please contact us at 800.535.2671.

Содержание Revolution HD 1999-0520


































Результаты поиска

Содержание Revolution HD 1999-0520

Отзывы:

Bayne Revolution HD 1999-0520, Руководство по эксплуатации и запасным частям, Страница: 7 / 52

Результаты поиска

Содержание Revolution HD 1999-0520

Отзывы: