manualshive.com logo in svg

baxter SP600 Series, Руководство по эксплуатации и установке

Поделиться
Скачать
baxter SP600 Series Скачать руководство пользователя страница 14

– 14 –

Operating Hints

•  To interrupt the water delivery, press STOP/0.

•  To continue dispensing, press START/RESUME.

•  To cancel dispensing, press SET AMOUNT.

•  The amount of water dispensed is displayed in the WATER AMOUNT DELIVERED window. When 

the delivery is complete, the display will blink and indicate 0 POUNDS 0 OUNCES.

•  If the set temperature is not reached within the preset time allowed (see Flush Time), the meter will 

fl

 ash and beep until a new temperature is set, the amount is changed or the START/RESUME button 

is pressed. If the START/RESUME button is pressed, the meter will deliver the set amount.

•  To get better results, always discard the 

fi

 rst water sample when the new temperature is entered 

or the unit has not been operated longer than 15 minutes.

USING THE TEMPERATURE PROBE

  1. Verify that the hand held temperature probe is plugged into the end of the 

fl

 exible cable attached to 

the bottom panel of the meter.

  2.  Place the end of the probe where the temperature needs to be measured. The HAND HELD PROBE 

TEMPERATURE window will display the temperature reading.

NOTE: 

The probe can be used to measure the temperature of the room, dough or 

fl

 our in the range of 

32°F (0°C) to 125°F (52°C). The probe must be in place for 30 seconds to get an accurate temperature 
reading.

Locking and Unlocking the Change Units

The CHANGE UNITS key can be locked to prevent it from being changed. To access Locking and Unlocking 
the Change Units parameter, follow the steps below:

 1. 

Press 

SET 

TEMP.

  2. Enter 32 using the numeric keypad.

 3. 

Press 

SET 

AMOUNT.

  4. Enter 94404 using the numeric keypad. The WATER AMOUNT SETTING window displays 

944 lbs 04 oz.

  5. Press START/RESUME. The WATER TEMPERATURE SETTING window displays 

0

 (Units is not 

locked) or 

1

 (Units is locked).

  6. Enter desired value on the numeric keypad. If no change is desired, proceed to the next step.

  7. Press START/RESUME to save the setting.

Содержание SP600 Series





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды