baxter Flo-Gard 6301 Скачать руководство пользователя страница 113

Страница: 113 / 252

07-19-B1-729

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

9-3

Calibration

DC Line Voltage Calibration

Figure 9-1 Calibration Equipment Setup

14.2

Separate the front and rear housings completely in accordance
with “Separation of Front and Rear Housings” on page 8-5.

14.3

Disconnect the power supply connector (CN301) from the CPU
board (Figure 11-2 , item 2) and connect it to the resistive load.

14.4

Connect the resistive load as illustrated in Figure 9-1 with the
positive lead connected to pin 2 and the negative lead
connected to pin 3.

14.5

Plug all calibration equipment into a 115 ± 5.0 VAC, 60 Hz
power source. Set as follows:

•

Variable transformer: 0 V or minimum setting.

•

Minimum current setting: constant current mode.

14.6

Turn potentiometers VR1 and VR2 on the DC power supply
board (Figure 11-3 , item 17) fully clockwise.

14.7

Set the DC ammeter to the appropriate range and the DC
voltmeter to 20 VDC range. Do not use autorange.

Calibration of Output Current Limit by VR2

14.8

Ensure the AC power plug of the pump is connected to the
variable transformer.

14.9

Adjust the variable transformer output to 120 VAC. The
voltage may be checked with an ordinary tester with ±3%
accuracy.

14.10

Adjust the potentiometer until the output current is 1.40 A.

Variable

Transformer

0.5 A SB

AC In

Power

Transformer

DC Power Supply

Board

CN301

Pump

Resistive Load

5 Ohm

20 W

5 Ohm

20 W

Содержание Flo-Gard 6301





























































































































































































































































Результаты поиска

Содержание Flo-Gard 6301

Отзывы:

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 113 / 252

Результаты поиска

Содержание Flo-Gard 6301

Отзывы: