Compound Mitre Saw – CM-210
E&OE
© 2020 Baumr-AG
6
•
Do not use saw blades made of high speed steel.
•
Check the condition of the saw blades before using the crosscut, drag and mitre saw.
•
Make sure that a suitable saw blade for the material to be cut is selected.
•
Only use saw blades recommended by the manufacturer. Saw blades designed to cut wood and similar materials must comply with EN 847-1.
•
Do not use saw blades made of high-speed alloy steel (HSS steel).
•
Only use saw blades for which the maximum permissible speed is not lower than the maximum spindle speed of the crosscut, drag and mitre
saw, and which are suitable for the material to be cut.
•
Observe the saw blade direction of rotation.
•
Only insertion the saw blade if you have mastered their use.
•
Observe the maximum speed. The maximum speed specified on the insertion tool may not be exceeded. If specified, observe the speed range.
•
Clean grease, oil and water off of the clamping surfaces.
•
Do not use any loose reducing rings or bushes for the reducing of holes on saw blades.
•
Make sure that fixed reducer rings for securing the insertion tool have the same diameter and have at least 1/3 of the cutting diameter.
•
Make sure that fixed reducer rings are parallel to each other.
•
Handle insertion tool with caution. They are ideally stored in the originally package or special containers. Wear protective gloves in order to
improve grip and to further reduce the risk of injury.
•
Prior to the use of insertion tools, make sure that all protective devices are properly fastened.
•
Prior to use, make sure that the insertion tool meets the technical requirements of this electric tool and is properly fastened.
•
Only use the supplied saw blade for cutting wood, never for the processing of metals.
•
Only use saw blade diameters in accordance with the markings on the saw.
•
Use additional workpiece supports, if required for workpiece stability.
•
Workpiece support extensions must always be secured and used during work.
•
Replace table inserts when worn!
•
Avoid overheating of the saw teeth.
•
When sawing plastic, avoid melting of the plastic.
•
Use the appropriate saw blades for this purpose.
•
Replace damaged or worn saw blades immediately.
•
When the saw blade overheats, stop the machine.
•
Allow the saw blade to cool down before using the machine again.
•
Attention: Laser radiation Do not stare into the beam Class 2 laser.
•
Protect yourself and your environment from accidents using suitable precautionary measures!
•
Do not look directly into the laser beam with unprotected eyes.
•
Never look into the path of the beam.
•
Never point the laser beam towards reflecting surfaces and persons or animals. Even a laser beam with a low output can cause damage to the
eyes.
•
Caution - methods other than those specified here can result in dangerous radiation exposure.
•
Never open the laser module. Unexpected exposure to the beam can occur.
•
If you do not use the device for a long time, the batteries should be removed.
•
The laser may not be replaced with a different type of laser.
•
Repairs of the laser may only be carried out by the laser manufacturer or an authorised representative.
RESIDUAL RISKS
The machine has been built according to the state of the art and the recognised technical safety requirements. However, individual
residual risks can arise during operation.
•
Health hazard due to electrical power, with the use of improper electrical connection cables.
•
Furthermore, despite all precautions having been met, some non-obvious residual risks may still remain.
•
Residual risks can be minimised if the “safety instructions” and the “Proper use” are observed along with the whole of the operating instructions.
•
Do not load the machine unnecessarily: excessive pressure when sawing will quickly damage the saw blade, which results in reduced output of
the machine in the processing and in cut precision.
•
When cutting plastic material, please always use clamps: the parts which should be cut must always be fixed between the clamps.
•
Avoid accidental starting of the machine: the operating button may not be pressed when inserting the plug in an outlet.
•
Use the tool that is recommended in this manual. In doing so, your machine provides optimal performance.
•
Hands may never enter the processing zone when the machine is in operation.
•
Release the handle button and switch off the machine prior to any operations.
