Baumfolder BAUM 2018 Скачать руководство пользователя страница 11

Страница: 11 / 50

PAGE 11 TP10313

1.0

Control Panel BAN-5

Figure 1. Control Panel.

1.1 Displays

01) Large Display

Eight digit multi use display composed of 7-

segment LEDs.

02) Small Display

Three digit multi use display composed of 7-

segment LEDs.

03) Ten segment bar graph display

The suction length display is used to display the

Suction Length as a percentage of Sheet Length.

This allows a range from 5% to 50%.

1.2 Machine Status Indicators

04) Suction Indicator

The suction indicator will track the suction

output. The LED will turn on when the suction

output turns on.

05) Pile indicator

The indicator is lit when the feeder is in auto-

matic feed mode. The indicator will flash if the

feeder is in reverse mode (Continuous Feeder) or

moving down (Pile feeder)

BAUMFOLDER

CORPORATION

06) Input Indicator

The input indicator shows the status of the suction

photo-eye.

07) Output Indicator

The output indicator lights when the Batch Preset

is reached and the user has selected a batching

option. The output indicator is lit during the time

the batching option is active.

Batching options are Feed interruption, Speed up

table, Marking table or Kicker.

1.3 Machine Control Pushbuttons

08) Main Drive Start

09) Main Drive Stop

10) Pump Start

11) Pump Stop

12) Feeder Start

13) Feeder Stop

14) Pile Feeder Up, Continuous Feeder Start

15) Pile Feeder Stop, Continuous Feeder Stop

16) Pile Feeder Down, Continuous Feeder Reverse

17) Emergency Stop

Содержание BAUM 2018



















































Результаты поиска

Содержание BAUM 2018

Отзывы:

Похожие инструкции для BAUM 2018

Бренды по названию

Популярные бренды

Baumfolder BAUM 2018, Инструкция по эксплуатации

Результаты поиска

Содержание BAUM 2018

Отзывы:

Похожие инструкции для BAUM 2018

Бренды по названию

Популярные бренды