Baumer Hubner Berlin microGen PMG10 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 40

Baumer Hubner Berlin microGen PMG10 Скачать руководство пользователя страница 17

Baumer Hübner

Installation

|

5

V1 | PMG10 & PMG10P Profibus DP

Operating Manual

17

g) Fasten the coupling onto the shaft of the drive at a torque of 1.3 ±10 % Nm.

Observe the remarks in the data sheet and the coupling assembly instructions.

5.3

Maximum permitted tolerances for mounting errors when using the
Baumer Hübner K 35 spring washer

NOTICE

Damage to the encoder ball bearings.

Hard impacts of the drive shaft imposed on coupling parts may damage the ball bearings.

a) Prevent any hard impacts of the drive shaft on coupling parts.

Instruction:

a) Mount the drive with small angular error and parallel offset.

b) Note the following allowable mounting errors:

The figure shows the device with EURO flange B10, the same maximum permissible mounting
errors must be observed for the device with housing foot B3.

±0.7 (±0.3*)

±0.2 (±0.05*)

±1°

* With insulated plastic hub

Permitted parallel misalignment

Permitted angle error

Permissible axial movement

Ill. 7:

Permissible mounting errors (dimensions in mm)

«
...
15
16
17
18
19
...
»

Содержание Hubner Berlin microGen PMG10









































Отзывы:

Нет отзывов