Baumer 11188367 Скачать руководство пользователя страница 24

Страница: 24 / 29

Manual R600V.DAE0 (EN)

Page 24 of 29

R600V.DAE0_manual_1.5 (EN).docm

Last Update: 07 Jan 2021

Trouble Shooting

Tab 15

Trouble Shooting Overview

Failure

Action

No function, no LED

Check cables, connections, power supply at pins

Function impaired, thick layer of dirt

Clean lens and remove excess water.

Mechanical damage to housing
and/or lens

Replace part by qualified personnel.

Unexplained targets / distance meas-
urement in near range

Check free space (or beyond) for non-stationary objects (such as dangling wires,
tubes, water drops on surfaces.

Unexplained targets / distance meas-
urement in far range

Check for double reflections, and limit measurement range

The LED is blinking red (50ms on /
50ms off)

Hardware fault. Replace part by qualified personnel

The LED is blinking magenta

CAN bus error. Check Tab 5 for details.

The LED is blinking blue for a long pe-
riod.

Try a power cycle. If this does not fix the issue replace part by qualified personnel

No communication (also magenta
blinking)

Check CAN speed (e.g. 250kbit/sec), check 120Ohm termination,

Accessories

The following accessories are available for this product

Tab 16

Accessories

Art. no.

Description

Type

Comment

11213075

ZCABL-ALL.AMP0300

Connector AMPSEAL 16 with
PUR-cable

3m cable with AMPSEAL connector
and fly-leads

Содержание 11188367






























Результаты поиска

Содержание 11188367

Отзывы:

Бренды по названию

Популярные бренды

Baumer 11188367, Руководство по эксплуатации

Результаты поиска

Содержание 11188367

Отзывы:

Бренды по названию

Популярные бренды