background image

5 SERVICE AND 

MAINTENANCE

5.1 Safety

 WARNING

Prevent death or serious injury.

1. 

Park machine on firm, level surface.

2. 

Engage park brake.

3. 

Verify all controls are in neutral.

4. 

Stop engine and remove key.

 

WARNING

Prevent death or serious injury.

Raised unsupported lift arms can fall, 

resulting in death or serious injury.

Never enter the area under raised lift 

arms.

5.2 Daily Or Every 10 Hours

Check Engine Oil Level

1. 

Refer to OEM engine manual for detailed 

maintenance information. Skidsteer must be 

parked on a level surface, park brake engaged, 

lift arms fully lowered, engine stopped and key 

removed. 

2. 

Loosen knobs (A) and pivot hydraulic oil cooler 

upward. Engage pin to hold cooler in open 

position.

A

A

3. 

Check oil level on dipstick. Oil level should be 

at  full  mark  on  dipstick.  Add  OEM  specified 

engine  oil  as  necessary  through  fill  port  on 

engine.  

The  OEM  engine  manufacturer  specifies  the  oil 

be a 4-stroke motor oil that meets or exceeds the 

requirements for API service category SJ or later 

(or equivalent). 

50 to 105° F  (10 to 40° C) 30W
5 to 105° F  

(-15 to 40° C)

5W-30 or 10W-30 

-15 to 105° F  

(-25 to 40° C)

Synthetic 5W-30

SAE 10W-30 or 5W-30 is recommended for 

general use. Use a full synthetic for starting/

operating temperatures between 5 to -13° F (-15 

to -25° C). Other viscosities shown may be used 

when the average temperature in your area is 

within the indicated range.

24

Содержание WRL58G









































Отзывы: