Baumalight DSA530 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 28

Baumalight DSA530 Скачать руководство пользователя страница 22

5�4 Replace Cutting Teeth

1. Park tree saw on a level surface.
2. Lower blade to the ground.
3.

Shut off engine and lockout engine controls.

4. Inspect cutting teeth (B) for damage and wear.

Replace individual teeth as needed.

5. Remove locknut (A) and tooth (B). Install new

tooth. Flat shoulder on tooth will fit against

shoulder (C) on tooth holder.

6. Install locknut. Tighten locknut (A) to 65 lb/ft

(88 Nm) of torque.

A

B

C

Note:

Parts breakdown can be found on

Baumalight’s website. www.baumalight.com

Check cutting teeth every 4 hours of use. Keep

cutting teeth in good condition. Unit will cut faster

and remaining teeth will last longer if broken or

worn teeth are replaced.

Each tooth can be rotated up to two times from its

original position before replacement is necessary.

1. Park tree saw on a level surface.
2. Lower blade to the ground.
3.

Shut off engine and lockout engine controls.

4. Inspect teeth for wear on top edge. Once top

edge is worn, rotate tooth so a new edge is on

top (cutting) edge.

5. Loosen locknut (A) on tooth (B) and rotate

tooth 1/3 turn. Flat shoulder on tooth will fit

against shoulder (C) on tooth holder.

6. Tighten locknut (A) to 65 lb/

ft (88 Nm) of torque.

A

B

C

Note:

Parts breakdown can be found on

Baumalight’s website. www.baumalight.com

5�3 Rotate Cutting Teeth

20

«
...
20
21
22
23
24
...
»

Содержание DSA530





























Отзывы:

Нет отзывов