manualshive.com logo in svg

Bauer S300, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Bauer S300 Скачать руководство пользователя страница 13

 

 

 

Operating Manual for 

BAUER Separator S300

 

7 

 

 

Ventilation 

 

4

 

SETUP OF THE SEPARATOR 

4.1  INSTALLATION DIAGRAM 

 

 

 

 
 

 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 

 
 

4.2  CONDITION OF THE BAUER SEPARATOR UPON DELIVERY 

The BAUER separator was developed by the company BAUER GesmbH. The separator is delivered as a 
unit, including installed electric motor, on a pallet. The inflow element with outlet for overflow and ventila-
tion as well as the ventilation pipe are enclosed separately for easier transport and must be installed be-
fore the initial startup. 

You must connect the geared motor of the separator to the power supply of the optionally available switch 
cabinet and connect this to the electricity supply. It is recommended that the corresponding electrical con-
trol for the separator or for the separator and the BAUER submersed motor pump be purchased from 
BAUER since it will be already adapted to the corresponding drive motors.  

Connecting the supplied hoses, if included, to the inflow and discharge connections of the machine com-
pletes the installation of the BAUER separator.  

 

DANGER 

 

Work on electrical and electronic components of the system may only be performed 
by a trained electrician or otherwise appropriately trained personnel under the guid-
ance and supervision of a trained electrician in accordance with the applicable elec-
trical and electronic regulations. 

 

4.3  REQUIRED TOOLS 

Special tools are not required for setting up the separator. 
Standard tools for assembly and electrical tools are required for assembly, setup and disassembly. 
 
The  customer  must  check  based  on  the  dimensions  and  weight  of  the  separator  whether  the  available 
lifting  equipment  (forklift,  tractor  with  front  loader,  crane  with  corresponding  belts  or  chains)  is  sufficient 
for setting up the separator. 

Distribution of the 
solid phase 

Sale of the solid 
phase 

Composting of 
the solid phase 

BAUER 
Separator  
S300 

BAUER MAGNUM 
pump system 

Distribution of the 
liquid phase 
via BAUER 
slurry injector 
Cerres 

Distribution of the 
liquid phase 
via BAUER 
Pivot or Rainstar 

BAUER  
submersed 
motor pump 
MAGNUM  

BAUER  
slurry mixer  

BAUER  
submersed 
motor stirrer 
TMRW 

BAUER eccentric 
spiral pump 
Helix 

Liquid 
phase 

Solid 
phase 

Inflow 

Overflow 

BIOGAS PLANT 

Fig. 4-1 Installation diagram 

Содержание S300










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды