manualshive.com logo in svg

Bauer G 120 II V, Инструкция по эксплуатации и список запасных частей, Страница: 88 / 138

Поделиться
Скачать
Bauer G 120 II V Скачать руководство пользователя страница 88

G 120 II V

Page 78

 

1st Edition, Rev. 0 Chg. 2

 

6.4.2

Replacing the PLC 

Replacing the PLC does not require removal of any wiring as the connections are made with push in Con-
nector Blocks. To replace the PLC proceed as follows.

1. Turn off unit and disconnect from main power supply.

2. Lift the Input Connections Cover. See Figure 6-3, Item 5.

3. Insert a small flat bladed screwdriver in the notch in the back center of the Connector Block. Gently 

pry the Connector Block loose. See Figure 6-4.

4. Repeat Steps 2 and 3 for the to the Connector Block on the Output side of the PLC.

5. The Power Connector on the side opposite side from the DIN Rail Clip, Figure 6-3, Item 7, is 

removed by pulling it straight out from the PLC.

6. Unclip the PLC from the DIN Rail by using a small flat bladed screwdriver to pull the DIN Rail 

Clip out until the PLC is free.

7. Replace the PLC and slide the DIN Rail Clip in with the screwdriver until it is secure.

8. Replace the Power Connector by pushing it into the socket in the side of the PLC.

9. The Connector Blocks are replaced by pushing them gently down onto corresponding pins until 

they click into place.

10. Restore power and operate the unit.

6.4.3

Installing a New Program

The PLC program can be updated in two ways. If a Bauer technician is on-site, they will connect directly 
to the PLC using a notebook computer. Another method to install a new program is to use an External 
EEPROM cartridge. The EEPROM would be programmed at the Bauer factory and shipped either to the 
customer or to a authorized distributor.

6.4.4

Installing an EEPROM

To install or replace an EEPROM Cartridge proceed as follows:

1. Turn off unit and disconnect from main power supply.

2. Lift straight up to remove the EEPROM cover. Keep the cover. See Figure 6-3, Item 9.

3. The EEPROM is keyed to fit only one way and requires minimal force to insert it. 

4. Push the EEPROM down until it snaps into place.

5. If the EEPROM is being retained in the PLC, restore power to the unit and operate as normal.

6. If the EEPROM is for a software update and is to be returned to Bauer or a distributor continue as 

follows.

7. Restore power to the unit.

8. After the software has initialized and the Home Screen is displayed, shutdown the unit and discon-

nect from the main power source. 

9. Restore power to the unit. After the software has initialized a second time and the Home Screen is 

displayed, shutdown the unit and disconnect from the main power source.

Содержание G 120 II V











































































































































Отзывы:

Нет отзывов