background image

Page 12

For technical questions, please call 1-888-866-5797.

Item 57180 

        

S

AFE

ty

Op
ERA

ti

O

n

M

A

int
E

n

A

nc
E

S

E

t

U

p

General Operating instructions

1.  Make sure that the Trigger is in the 

off-position, then attach a fully charged 
Battery Pack making sure it clicks in place.

2.  Before each use, test the tool as 

directed in the prior section.

WARninG!  tO pREVEnt 
SERiOUS inJURy:  Keep second hand 
away from tool discharge area, 
especially if holding workpiece.  
tool applies extreme force to fastener, 
and fasteners may deflect or discharge 

in an unexpected direction.
WARninG!  tO pREVEnt inJURy:  
Do not hold tool near body while driving.  
tool recoil can cause injury.

WARninG!  tO pREVEnt SERiOUS 
inJURy, incLUDinG pERMAnEnt 
HEARinG LOSS:  Always wear hearing 
protection when using the tool.

3.  Position tool at desired fastener location, set 

the Activation Mode Switch, and depress the 
Workpiece Contact fully against the workpiece.   
Squeeze the Trigger to discharge a fastener.

4. 

to change driving depth:

  

Disconnect Battery 

pack and keep Workpiece contact pointed 
away.

   

To reduce nail depth, turn the Depth Knob 
clockwise, toward  . 
To increase nail depth, turn the Depth 
Knob counterclockwise, toward  .

Depth 

Knob

5. 

the LED indicator:

LED indicator

a.  Flashing red indicates a jam in the 

Magazine.  Stop and clear the jam.

b.  Solid red indicates low battery.  Remove 

Battery Pack and recharge it.

c.  Flashing green indicates the tool is over 

heating.  Stop using the tool immediately and 
allow it to cool down before continuing use.

d.  Solid green indicates no fasteners are in 

the Magazine.  Stop and reload tool.

e.  If the LED is not illuminated this indicates 

the battery is fully charged and the 
fasteners are correctly installed.

6. 

After use, to prevent accidents:

a. 

Release the trigger.

b. 

Remove the Battery pack.

c. 

Empty the Magazine.

d. 

Attempt to discharge the tool into a piece of 
scrap wood to ensure that it is disconnected 
and is incapable of driving any fasteners.

e. 

Release the trigger again.

f. 

clean external surfaces with clean, dry cloth.

7. 

Store indoors out of children’s reach.

Содержание 20131C-B





















Отзывы: