Bauer 1865E-B Скачать руководство пользователя страница 15

Страница: 15 / 20

Page 15

For technical questions, please call 1-888-866-5797.

Item 64856

ERA

MAINT

ENANC

TUP

Grinding, and Wire Brushing Instructions

TO PREVENT SERIOUS INJURY: Grip the tool firmly in both hands.

1. Make sure that the Power Switch is in

the off-position, then plug in the tool.

2. Place one hand on the motor housing the other

on the side handle before starting the tool.

3. Start the tool by pressing the Power

Switch forward until it locks in place.

4. Allow the tool to come up to full speed

before touching the work material.

5. Apply the wheel to the work material at a 10° – 15°

angle, allowing the tool to operate at full speed.

If the tool bogs down, use lighter pressure.

6. To create a smoother surface,

keep the tool moving over the work surface.

TO PREVENT ACCIDENTS, AFTER USE:

Turn off the tool by pushing the

Power Switch backward.

WARNING! Allow the tool to come to a complete

stop before setting it down.

Unplug the tool. Clean, then store the

tool indoors out of children’s reach.

Sanding Instructions

TO PREVENT SERIOUS INJURY: Grip the tool firmly in both hands.

1. Wipe the work surface clean of all dirt and debris,

especially that of previous

coarser sanding sessions, which will scratch

the surface of a finer grit sanding session.

2. Attach the desired grit Sanding Disk

(sold separately) onto the Spindle.

3. Make sure that the Power Switch the

off-position, then plug in the tool.

4. Start the tool by pressing the Power

Switch forward until it locks in place.

5. Wait until the tool has reached full speed,

then gently contact the surface.

6. Keep heavy pressure off of the tool when operating.

Allow the tool to do the work.

7. Move the tool in a uniform pattern up and down or

side to side while sanding to ensure even sanding.

8. Periodically, stop the tool and check for disc wear.

Replace worn sanding discs as needed.

TO PREVENT ACCIDENTS, AFTER USE:

Turn off the tool by pushing the

Power Switch backward.

WARNING! Allow the tool to come to a complete

stop before setting it down.

Unplug the tool. Clean, then store the

tool indoors out of children’s reach.

Содержание 1865E-B





















Результаты поиска

Содержание 1865E-B

Отзывы:

Похожие инструкции для 1865E-B

Бренды по названию

Популярные бренды

Bauer 1865E-B, Руководство пользователя и инструкции по безопасности

Результаты поиска

Содержание 1865E-B

Отзывы:

Похожие инструкции для 1865E-B

Бренды по названию

Популярные бренды