Batavia PSR-5014 Скачать руководство пользователя страница 4

 

 
 

located in the front and two located in the rear) have been built into the left and right side 
frames. 
The two front  adjusting screws enable  the operator to raise or lower the pinch roll,  so 
that the correct gap between the upper and lower pinch roll may be obtained to feed the 
desired stock in to the machine. 
The left and right rear adjusting screws assist the operator in raising or lowering the idler 
roll  which  determines  the  degree  of  bend  in  the  stock  that  is  being  fed  through  the 
machine.  The  right  and  left  side  frames  are  each  equipped  with  a  scale  to  aid  the 
operator in determining. 
7.  TO  REMOVE  THE  FORMED  PART-  lift  clamp  handle  and  slide  the  support  lever 
handle to the right. The upper pinch roll will rise. Slide the material off roll. If the material 
is not long enough or if the formed part is not the proper diameter, additional samples 
will  have  to  be  made.  Thousands  of  identical  parts  can  be  precisely  duplicated  when 
proper adjustment of the roller have been made. 
 
 
 
8. REVERSE ROLLING CIRCLES- the same diameter as the diameter of the rolls and 
slightly larger, can be formed with the Roller in just one pass. To make the adjustment for 
material thickness and to determine the length of material needed, see the instructions 
given under “How To Form Circles In Just Two Passes”. 
 
 
 
 
 
 

IV Electric System 

 

1, Preparation :The consumer should prepare a 10A power switch. Connect 3x4 mm

2

 + 

1x4mm

yellow/green  with  the  power  switch.  The  earth-line  should  be  connected  with 

the earth-plate. 
2, Operation of the machine 
Combine the breaker in the electric appliance box and turn right the power switch. At this 
time  the  indicator  lighted,  which  means  the  machine  had  been  connected  with  power 
correctly. Pedal down the right starting pedal, the machine rolls clockwise continuously 
until  loosen  the  pedal.  Pedal  down  the  left  starting  pedal,  the  machine  rolls  on  the 
contrary  of  the  above  direction.  If  there  is  some  wrong  with  the  machine,  push  the 
lash-up switch on the handle to stop the machine. After the trouble is solved, turn off the 
switch to work.   
3, Maintenance of the machine 
The machine has a compact structure. It is easy to be operated and maintained. Some 
problems maybe exist as follows: 

BATAVIA MACHINERY - 877-528-2809

BATAVIA MACHINERY - 877-528-2809

Содержание PSR-5014










Отзывы: