Batavia 7063487, Руководство по эксплуатации

Страница: 11 / 50

9
English
11.2
How to use the Presta valve adaptor
The Presta valve adaptor can be used for
Presta valve stems as described below.
Before inflating a tyre with a Presta valve,
loosen the locking nut on top of the valve.
Once Inflation is complete, tighten the lock-
ing nut to seal the tyre valve.
• Loosen the Presta valve locking nut.
• Thread the Presta valve adaptor onto
the valve stem with the adaptors interior
threads.
• Position the air chuck clamp in the
unlock position.
• Clamp the end of the air chuck down
onto the Presta valve adaptor by press-
ing air chuck clamp down until it locks
into place.
• Inflate the tyre.
• After inflation, remove air chuck and
Presta valve adaptor and tighten locking
nut with your fingers. Do not use tools.
11.3
Accessories storage
When not in use, adaptors and needles
provided with the compressor can be
placed in the storage area (7) located on
the right side of the compressor.
11.4
Hoses storage
When not in use, the hoses provided with
the inflater can be placed in the storage
areas located on both sides of the
compressor.
12. Work light
The compressor is equipped with a work
light (5) . The work light will be automatically
switched on when power switch is at the
position of “I” or “II”. It will be switched off
automatically when the power switch is at
the position “O”.
13. Cleaning and maintenance
WARNING: Remove the battery before car-
rying out any maintenance/cleaning of the
tool.
13.1
Cleaning
• Use only a moist cloth to clean the unit.
Do not use aggressive chemicals which
may dissolve plastic parts, or abrasives.
Always keep the ventilation slots clean
and free from obstructions.
• Keep safety devices, ventilation open-
ings and the motor housing as free as
possible from dirt and dust. Rub the
electric power tool with a clean cloth or
blow over it with low pressure com-
pressed air.
• We recommend that you clean your
electric power tool immediately after
each use.
• Clean the electric power tool regularly
with a damp cloth and somewhat soft
soap.
13.2
Maintenance
There are no inner parts of the tool which
need maintenance.
14. Technical data
No load speed . . . . . . . . . . 16000 min
-1
Max. air pressure . . . . . . . 150 psi/10 bar
Length of high pressure hose . . . . . 67 cm
Length of low pressure hose. . . . . . 29 cm
Product weight without battery . . . 1.45 kg
Product dimensions. . 24.5 × 15.1 × 18.4 cm
Sound pressure level L
pA
. . . . . . 77 dB(A)
Uncertainty K
pA
. . . . . . . . . . . . . . 2.8 dB
Sound power level L
WA
. . . . . . . 97 dB(A)
Uncertainty K
WA
. . . . . . . . . . . . . 2.8 dB
Hand arm vibration . . . . . . . . . 2.3 m/s
2
Uncertainty K. . . . . . . . . . . . . .0.1 m/s
2
15. Disposal
Do not dispose of electric power
tools with domestic refuse.
The electric power tool is shipped in
packaging to reduce transport damage.
This packaging is a raw material and as
such can either be reused or can be fed
back into the raw material cycle. The elec-
tric power tool and its accessories are
made from various materials such as met-
als and plastics. Take defective compo-
nents to a special refuse collection point.
Ask about these at your specialist shop or
local council. The product and the user
manual may be subject to changes. Techni-
cal data may be changed without prior
notice.