background image

 

BASSRA MACHINE TOOLS LTD. 

99 Spring Road, Tyseley, Birmingham, United Kingdom, B11 3DJ 

Tel: 0044 (0) 121 707 4343 / Fax: 0044 (0) 121 707 3535 

Website: www. bassra.com / Email: [email protected]

 

 
 
CAREL CONTROLLER 
 
 The SEL symbol should be pressed for two seconds.  ST1 will start to flash and its 
setting will be displayed.  Press the up and down symbols until the desired 
temperature is reached.  Press SEL again and ST2 will be displayed.  (Care should be 
taken not to adjust ST2 set point as this could stop the machine working if done 
incorrectly).  Press SEL again to exit setup.   
 
TECHNOLOGIC CONTROLLER 
 
Push key “P” then release it and the display will visualise “SP1”.  To modify the valve, 
press “UP” key to increase it or the “DOWN” key to decrease it.  Once the desired 
valve has been reached by pushing “P” it is possible to check AL1, (the under 
temperature valve set and locked at 165

°

C).  Push “P” once again to exit 

programming. 
 
Care should be taken not to adjust any other set points, as this could stop the 
machine if done incorrectly. 
 
MAINTENANCE 

 

All maintenance should be carried out by approved B.M.T. engineers. 
 
Keeping the machine clean is often overlooked, particularly with regard to the hose.  
The hose should have a piece of carpet, or similar, placed under it where contact is 
made with the floor.  This prolongs the life of the hose, but only if the carpet is kept 
clean and free from pieces of debris, especially glass.  
                                                                                                                                                                                             
                                                                                                                                                                                                                                                                                                                         
 

Содержание BMT 1000


















Отзывы: