Basler BE1-50B-235 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 67

background image

9252000898 Rev —

BE1-50/51B-235/-236 Characteristic Curves

A-1

APPENDIX A

•

CHARACTERISTIC CURVES

INTRODUCTION

This appendix describes and defines the instantaneous overcurrent, time overcurrent, and integrating
time reset characteristics of the BE1-50/51B-235 and BE1-50/51B-236 relays.

INSTANTANEOUS OVERCURRENT CHARACTERISTICS

Timing

The instantaneous characteristic curves of the BE1-50/51B-235 and BE1-50/51B-236 relays are similar to
standard electromechanical instantaneous units. However, the time to trip for applications where the initial
sensing current is less than 400 mA may be slightly longer. This may occur on a very lightly loaded circuit
or when the relay is providing ground protection and is connected to measure neutral current. Figure A-1
shows the instantaneous characteristic curves for the maximum time to trip.

Figure A-1. Instantaneous Characteristic Curves

The delay of the Instantaneous A (50-A) element can be set for no intentional delay (switch SW3-2 open)
or a fixed delay of 100 ms (SW3-2 closed). Figure 2-2 illustrates the location of SW3. The time delay of
the 50-B element is not switch-selectable and is fixed at no intentional delay.

Pickup

The instantaneous elements of the BE1-50/51B-235 and BE1-50/51B-236 relays may be set lower than
the instantaneous element in IAC relays and still have the same reach. This is because the BE1-50/51B-
235 and BE1-50/51B-236 instantaneous elements effectively eliminate the fault current transient
overreach components. When setting the BE1-50/51B-235 and BE1-50/51B-236 instantaneous elements,
calculate the symmetrical value without any adder for transient overreach.

TIME OVERCURRENT CHARACTERISTICS

Nine inverse time functions and one fixed (definite) time function can be selected at the front panel. Curve
types are identified by a letter designator. Available curve types are short inverse (S), long inverse (L),
definite time (D), moderately inverse (M), inverse (I), very inverse (V), extremely inverse (E), BS142
inverse, (B), and BS142 extremely inverse (C).

www

. ElectricalPartManuals

. com

«
...
47
48
49
50
51
...
»

Содержание BE1-50B-235




































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-50B-235

Бренд: KAEL Страницы: 3

Бренд: Schweitzer Engineering Laboratories Страницы: 616

Бренд: Schweitzer Engineering Laboratories Страницы: 1518

Бренд: IDEC Страницы: 3

Бренд: TE Connectivity Страницы: 4

Бренд: ABB Страницы: 40

Бренд: ASO Safety Solutions Страницы: 28

Бренд: ABB Страницы: 20

Бренд: ABB Страницы: 16

Бренд: System Sensor Страницы: 2

MMR-U3-001-A230

Бренд: OEZ Страницы: 7

Pro Latch R 160

Бренд: Sterling Power Products Страницы: 21

Бренд: Woodward Страницы: 70

Бренд: turck Страницы: 22

Бренд: Pilz Страницы: 16

Бренд: Pilz Страницы: 19

Бренд: Pilz Страницы: 21

Бренд: Pilz Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды