Basler BE1-50/51B-229 Скачать руководство пользователя страница 33

Страница: 33 / 57

9252000892 Rev A

BE1-50/51B-229 Installation

4-3

From the reset characteristic curve equation:

seconds

)

(

−

Trip

set

M equals zero if the current decreases to zero. A negative result indicates reset time.

The results from the two equations give a full trip time of 0.209 seconds and a full reset time of 15.5
seconds if the current goes to zero.

In the coordination timing diagram of Figure 4-3:

= 0.209 seconds (relay was at reset)

= value < T

because rewind has not gone to

zero

= value <T

because rewind has not gone to zero

Figure 4-3. Coordination Timing Diagram

The equation for the time to trip during rewind (before relay is reset) is:

FullRewind

RewindTime

FullTrip

Occurance

This

Trip

Second Operation:

seconds

0.040

209

Third Operation:

seconds

0.161

209

INSTALLING THE RELAY

Once the BE1-50/51B-229 relay is configured with the desired settings, it can be installed by performing
the following steps.

1. Remove the existing SFC relay from the case.

2. Attach the cover adaptor to the existing SFC relay case with the four screws provided.

3. Insert the BE1-50/51B-229 relay in the case and lock the relay in place with the cradle latches.

4. Install the connection plug from the SFC relay.

5. Install the BE1-50/51B-229 relay cover by positioning the interlocking bracket at the top of the

cover into the mating receptacle at the top of the cover adaptor plate. Secure the cover by
tightening the knob at the bottom of the cover.

Содержание BE1-50/51B-229


























































Результаты поиска

Содержание BE1-50/51B-229

Отзывы:

Похожие инструкции для BE1-50/51B-229

Бренды по названию

Популярные бренды

Basler BE1-50/51B-229, Инструкция по эксплуатации

Результаты поиска

Содержание BE1-50/51B-229

Отзывы:

Похожие инструкции для BE1-50/51B-229

Бренды по названию

Популярные бренды