Basler BE1-50/51B-214 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 70

background image

1-2

BE1-50/51B-214/-215/-223/-225 General Information

9252000994 Rev N

Internal switches provide for selecting system operating frequencies of 50 or 60 Hz, instantaneous
element delays of 0.0 or 0.1 second, characteristic curve group selection for either GE IAC or ABB type
curves, and instantaneous or integrating reset characteristics. Switch location and description is provided
in Section 2.

Advantages

BE1-50/51B-214/-215/-223/-225 overcurrent relays have many advantages over other overcurrent relays.
The primary advantages are:

•

Time characteristics are defined by equations and graphs

•

Field selectable time characteristics

•

Very low burden extends the linear range of the CTs

•

Self powered from the sensed current

•

Continuous automatic calibration

BE1-50/51B-214/-215/-223/-225 overcurrent relays may be tested without removing the relay from the
case. Shorting contacts are provided for all current inputs when the connection plugs or relay chassis is
removed from the relay case.

SPECIFICATIONS

BE1-50/51B-214/-215/-223/-225 overcurrent relays have the following features and capabilities.

Current Sensing Input

Continuous Current:

14 Aac

BE1-50/51B-214/-215/-223

One Second Rating:

400 Aac

Continuous Current:

2.8 Aac

BE1-50/51B-225

One Second Rating:

80 Aac

Time Overcurrent (51) Element

Setting the TIME PICKUP control at the minimum pickup setting places the relay in the most sensitive
state and may be used as a safety setting.

Setting Range:

0.5 to 15.9 Aac

BE1-50/51B-214/-215/-223 Pickup

Setting Increment:

0.1 Aac

Accuracy:

±

2%,

±

25 milliamperes at or above 0.5 ampere setting

Setting Range:

0.1 to 3.18 Aac

BE1-50/51B-225 Pickup

Setting Increment:

0.02 Aac

Accuracy:

±

2%,

±

5 milliamperes at or above 0.1 ampere setting

Dropout occurs at 95% of pickup value.

Dropout

0.0 to 9.9 seconds in 0.1 second steps.

Timing Range

The timing accuracy is the sum of

±

1 cycle,

±

2%. This accuracy applies to the range of 1.3 to 40 times tap

and is for a given measured multiple of tap. The measurement of the multiple of tap has an accuracy that
is the sum of

±

2%,

±

25 milliamperes for the BE1-50/51B-214/-215/-223 and

±

2%,

±

5 milliamperes for the

BE1-50/51B-225.

Timing Accuracy

«
...
10
11
12
13
14
...
»

Содержание BE1-50/51B-214







































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-50/51B-214

Бренд: Salus Страницы: 40

EMWS 84 903 020

Бренд: Crouzet Страницы: 2

Бренд: Danfoss Страницы: 32

Бренд: Schleicher Страницы: 6

Бренд: Velleman Страницы: 12

Бренд: OEZ Страницы: 12

Бренд: Taco Страницы: 2

Бренд: EUCHNER Страницы: 3

Бренд: EUCHNER Страницы: 3

Бренд: Viessmann Страницы: 4

Бренд: Philio Страницы: 6

Бренд: ABB Страницы: 9

Бренд: ABB Страницы: 10

Busch-Wachter 6812U-101-500

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 23

Бренд: ABB Страницы: 16

Бренд: ABB Страницы: 44

Бренд: ABB Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды