20
• Leave lids open.
• Shut off taps and main switches upline of appliances.
Following prolonged disuse, proceed as follows:
• Inspect the appliance thoroughly before using it again.
• Allow electric appliances to operate at the lowest temperatu-
re for at least 60 minutes.
INSTRUCTIONS FOR CLEANING
REMINDERS FOR CLEANING
The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules
• Disconnect the appliance electric supply, if present, before
carrying out any operation.
• Clean the satin fi nish stainless steel exterior surfaces, the
cooking wells and the surface of the hotplates every day.
• At least twice a year, have an authorized technician clean the
internal parts of the appliance.
• Do not use direct or high pressure water jets to clean the
appliance.
• Do not use corrosive products to clean the fl oor beneath the
appliance.
SATIN FINISH STAINLESS STEEL SURFACES
• Clean the surfaces with a cloth or sponge using water and
proprietary non-abrasive detergents. Follow the direction of
the satin fi nish lines. Rinse repeatedly and dry thoroughly.
• Do not use pan scourers or other iron items.
• Do not use chemical products containing chlorine.
• Do not use sharp objects which might scratch and damage
the surfaces.
Cleaning fan (mod.ventilated oven)
The ofan should be cleaned regularly. Excessive grease depo-
sited on the blades may cause themotor to overheat, thereby
preventing correct distribution of heat and uniform cooking.
INSTRUCTIONS FOR MAINTENANCE
REMINDERS FOR THE MAINTENANCE TECHNICIAN
The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules
• Read this manual carefully. It provides important information
for safe installation, use and maintenance of the appliance.
• Installation, conversion to a different type of gas and applian-
ce maintenance must be carried out by qualifi ed technicians
authorized by the manufacturer, in compliance with current
safety standards and the instructions in this manual.
• Identify the specifi c appliance model. The model number is
detailed on the packing and on the appliance data plate.
• The appliance must be installed in a well-ventilated room.
• Do not obstruct any air vents or drains present on the ap-
pliance.
• Do not tamper with appliance components.
13 CONVERSION TO A DIFFERENT TYPE OF GAS
See Chapter " Instructions for installation "
14 COMMISSIONING
Following installation, conversion to a different type of gas or
any maintenance operations, check appliance operation. In the
event of any malfunction, consult the next Paragraph "Trou-
bleshooting".
Switch on the appliance as directed in the instructions and re-
minders for use given in Chapter " INSTRUCTIONS FOR USE
" and check:
• the current values of each phase.
• the correct operation of the heating elements.
15 TROUBLESHOOTING
15.1
GLASS CERAMIC HOB
The radiant hotplate does not heat
Possible causes:
• Check the fuses
• Power supply main switch disconnected
• Insuffi cient voltage or incorrect electric connection of the ap-
pliance
• Defective energy regulator
• Element defective or not properly connected (burnt internal
heating element).
Heating cannot be adjusted
Possible causes:
• Temperature thermostat defective.
15.2 ELECTRIC
OVEN
The appliance does not heat.
Possible causes:
• Temperature thermostat defective.
• Heating elements defective.
• Safety thermostat tripped.
• Defective fan. ( mod. ventilated oven).
Heating cannot be adjusted
Possible causes:
• Temperature thermostat defective.
16 REPLACING COMPONENTS
REMINDERS FOR REPLACING COMPONENTS.
• Disconnect the appliance electric supply, if present, before
carrying out any operation.
• After replacing a gas system component, check for gas leaks
at connection points.
• After replacing an electrical system component, check it is
correctly wired.
• When replacing the radiant hotplates, handle and re-assem-
ble parts with the utmost care.
16.1
GLASS CERAMIC HOB
Replacing the radiant hotplates
• Remove the bottom of the appliance.
• Replace the faulty component.
Replacing the energy regulator
• Remove the bottom of the appliance.
• Replace the faulty component.
Glass ceramic hob
• In the event the glass ceramic hob is broken, contact our
company to have it replaced.
